Austenitic stainless steels (Fe-Cr-Ni) are resistant to hydrogen embrittlement but have not been studied using molecular dynamics simulations due to the lack of an Fe-Cr-Ni-H interatomic potential. Herein we describe our recent progress towards molecular dynamics studies of hydrogen effects in Fe-Cr-Ni stainless steels. We first describe our Fe-Cr-Ni-H interatomic potential and demonstrate its characteristics relevant to mechanical properties. We then demonstrate that our potential can be used in molecular dynamics simulations to derive Arrhenius equation of hydrogen diffusion and to reveal twinning and phase transformation deformation mechanisms in stainless steels.
Atomic scale defects critically limit performance of semiconductor materials. To improve materials, defect effects and defect formation mechanisms must be understood. In this paper, we demonstrate multiple examples where molecular dynamics simulations have effectively addressed these issues that were not well addressed in prior experiments. In the first case, we report our recent progress on modelling graphene growth, where we found that defects in graphene are created around periphery of islands throughout graphene growth, not just in regions where graphene islands impinge as believed previously. In the second case, we report our recent progress on modelling TlBr, where we discovered that under an electric field, edge dislocations in TlBr migrate in both slip and climb directions. The climb motion ejects extensive vacancies that can cause the rapid aging of the material seen in experiments. In the third case, we discovered that the growth of InGaN films on (0001) surfaces suffers from a serious polymorphism problem that creates enormous amounts of defects. Growth on surfaces, on the other hand, results in single crystalline wurtzite films without any of these defects. In the fourth case, we first used simulations to derive dislocation energies that do not possess any noticeable statistical errors, and then used these error-free methods to discover possible misuse of misfit dislocation theory in past thin film studies. Finally, we highlight the significance of molecular dynamics simulations in reducing defects in the design space of nanostructures.
Fe-Ni-Cr stainless-steels are important structural materials because of their superior strength and corrosion resistance. Atomistic studies of mechanical properties of stainless-steels, however, have been limited by the lack of high-fidelity interatomic potentials. Here using density functional theory as a guide, we have developed a new Fe-Ni-Cr embedded atom method potential. We demonstrate that our potential enables stable molecular dynamics simulations of stainless-steel alloys at high temperatures, accurately reproduces the stacking fault energy—known to strongly influence the mode of plastic deformation (e.g., twinning vs. dislocation glide vs. cross-slip)—of these alloys over a range of compositions, and gives reasonable elastic constants, energies, and volumes for various compositions. The latter are pertinent for determining short-range order and solute strengthening effects. Our results suggest that our potential is suitable for studying mechanical properties of austenitic and ferritic stainless-steels which have vast implementation in the scientific and industrial communities. Published 2018. This article is a U.S. Government work and is in the public domain in the USA.
Molecular dynamics (MD) simulations and experimental evaporation were applied to study the growth of evaporated (Cu)ZnTe on mono- and polycrystalline CdTe. The simulated structures show polytypism and polycrystallinity, including texturing and grain boundaries, diffusion, and other phenomena in excellent qualitative agreement with experimental atomic probe tomography, transmission electron microscope, and secondary ion mass spectrometry. Results show formation of Cu clusters in nonstoichiometric growths even at early stages of deposition. Results also show significantly faster diffusion along defected regions (uncorrelated CdTe grain boundaries) as compared with more highly crystalline areas (high-symmetry grain boundaries and pristine regions). Activation energies and pre-exponential factors of Cu, Zn, and Te diffusion were determined using simulation. The MD model captures crystal growth phenomena with a high degree of fidelity.
The growth dynamics and evolution of intrinsic stacking faults, lamellar, and double positioning twin grain boundaries were explored using molecular dynamics simulations during the growth of CdTe homoepitaxy and CdTe/CdS heteroepitaxy. Initial substrate structures were created containing either stacking fault or one type of twin grain boundary, and films were subsequently deposited to study the evolution of the underlying defect. Results show that during homoepitaxy the film growth was epitaxial and the substrate's defects propagated into the epilayer, except for the stacking fault case where the defect disappeared after the film thickness increased. In contrast, films grown on heteroepitaxy conditions formed misfit dislocations and grew with a small angle tilt (within ∼5°) of the underlying substrate's orientation to alleviate the lattice mismatch. Grain boundary proliferation was observed in the lamellar and double positioning twin cases. Our study indicates that it is possible to influence the propagation of high symmetry planar defects by selecting a suitable substrate defect configuration, thereby controlling the film defect morphology.
Reducing defects in InGaN films deposited on GaN substrates has been critical to fill the “green” gap for solid-state lighting applications. To enable researchers to use molecular dynamics vapor deposition simulations to explores ways to reduce defects in InGaN films, we have developed and characterized a Stillinger-Weber potential for InGaN. We show that this potential reproduces the experimental atomic volume, cohesive energy, and bulk modulus of the equilibrium wurtzite / zinc-blende phases of both InN and GaN. Most importantly, the potential captures the stability of the correct phase of InGaN compounds against a variety of other elemental, alloy, and compound configurations. Lastly, this is validated by the potential’s ability to predict crystalline growth of stoichiometric wurtzite and zinc-blende InxGa1-xN compounds during vapor deposition simulations where adatoms are randomly injected to the growth surface.
The Sandia HyMARC team continued its development of new synthetic, modeling, and diagnostic tools that are providing new insights into all major classes of storage materials, ranging from relatively simple systems such as PdHx and MgH2, to exceptionally complex ones, such as the metal borohydrides, as well as materials thought to be very well-understood, such as Ti-doped NaAlH4. This unprecedented suite of capabilities, capable of probing all relevant length scales within storage materials, is already having a significant impact, as they are now being used by both Seedling projects and collaborators at other laboratories within HyMARC. We expect this impact to grow as new Seedling projects begin and through collaborations with other scientists outside HyMARC. In the coming year, Sandia efforts will focus on the highest impact problems, in coordination with the other HyMARC National Laboratory partners, to provide the foundational science necessary to accelerate the discovery of new hydrogen storage materials.