Publications

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Acoustic-structure coupling can substantially alter the frequency response of air-filled structures. Coupling effects typically manifest as two resonance peaks at frequencies above and below the resonant frequency of the uncoupled structural system. Here, a dynamic substructuring approach is applied to a simple acoustic-structure system to expose how the system response depends on the damping in the acoustic subsystem. Parametric studies show that as acoustic damping is increased, the frequencies and amplitudes of the coupled resonances in the structural response undergo a sequence of changes. For low levels of acoustic damping, the two coupled resonances have amplitudes approximating the corresponding in vacuo resonance. As acoustic damping is increased, resonant amplitudes decrease dramatically while the frequency separation between the resonances tends to increase slightly. When acoustic damping is increased even further, the separation of the resonant frequencies decreases below their initial separation. Finally, at some critical value of acoustic damping, one of the resonances abruptly disappears, leaving just a single resonance. Counterintuitively, increasing acoustic damping beyond this point tends to increase the amplitude of the remaining resonance peak. These results have implications for analysts and experimentalists attempting to understand, mitigate, or otherwise compensate for the confounding effects of acoustic-structure coupling in fluid-filled test structures.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Finite element models are regularly used in many disciplines to predict dynamic behavior of a structure under certain loads and subject to various boundary conditions, in particular when analytical models cannot be used due to geometric complexity. One such example is a structure with an entrained fluid cavity. To assist an experimental study of the acoustoelastic effect, numerical studies of an enclosed cylinder were performed to design the test hardware. With a system that demonstrates acoustoelastic coupling, it was then desired to make changes to decouple the structure from the fluid by making changes to either the fluid or the structure. In this paper, simulation is used to apply various changes and observe the effects on the structural response to choose an effective decoupling approach for the experimental study.

Acoustoelastic coupling occurs when a hollow structure’s in-vacuo mode aligns with an acoustic mode of the internal cavity. The impact of this coupling on the total dynamic response of the structure can be quite severe depending on the similarity of the modal frequencies and shapes. Typically, acoustoelastic coupling is not a design feature, but rather an unfortunate result that must be remedied as modal tests are often used to correlate or validate finite element models of the uncoupled structure. Here, however, a test structure is intentionally designed such that multiple structural and acoustic modes are well-aligned, resulting in a coupled system that allows for an experimental investigation. Coupling in the system is first identified using a measure termed the magnification factor and the structural-acoustic interaction for a target mode is then measured. Modifications to the system demonstrate the dependency of the coupling with respect to changes in the mode shape and frequency proximity. This includes an investigation of several practical techniques used to decouple the system by altering the internal acoustic cavity, as well as the structure itself. Furthermore, acoustic absorption material effectively decoupled the structure while structural modifications, in their current form, proved unsuccessful. The most effective acoustic absorption method consisted of randomly distributing typical household paper towels in the acoustic cavity; a method that introduces negligible mass to the structural system with the additional advantages of being inexpensive and readily available.

Two novel and challenging applications of high-frequency pressure-sensitive paint were attempted for ground testing at Sandia National Labs. Blast tube testing, typically used to assess the response of a system to an incident blast wave, was the first application. The paint was tested to show feasibility for supplementing traditional pressure instrumentation in the harsh outdoor environment. The primary challenge was the background illumination from sunlight and time-varying light contamination from the associated explosion. Optimal results were obtained in pre-dawn hours when sunlight contamination was absent; additional corrections must be made for the intensity of the explosive illumination. A separate application of the paint for acoustic testing was also explored to provide the spatial distribution of loading on systems that do not contain pressure instrumentation. In that case, the challenge was the extremely low level of pressure variations that the paint must resolve (120 dB). Initial testing indicated the paint technique merits further development for a larger scale reverberant chamber test with higher loading levels near 140 dB.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

A series of modal tests were performed on an acoustoelastic system to explore how changes to the air and structural components affect the acoustoelastic coupling. This work is a continuation of previous experimental and analytical efforts. Here, the test method and perturbations were much more controlled than in previous tests, resulting in more refined data. Outputs of interest here are the coupled system modes as well as the resulting frequency response for various perturbations of the coupled system. Perturbations explored in this work include mass loading the structure, changing the air damping, and changing the air boundary conditions. Results of these tests indicate that simply adding damping to the air component, using foam or other absorptive material, is not sufficient to fully decouple the system. Rather, it is preferred to employ a change to the air boundary conditions, in the form of volume inclusions or scatterers, to prevent formation of the acoustic coupled mode.

Abstract not provided.

Abstract not provided.