Publications

Abstract not provided.

Abstract not provided.

Thin polymer films have been identified as one of the major enabling technologies for future space-based systems. Potential devices include those based on piezoelectric bimorph polymers that deform when a charge is deposited, for example, from an electron gun. The thin-film and lightweight nature of the polymeric devices will allow them to be launched more readily and deployed to operating conditions once in orbit. Until now little work has been done aimed at investigating the performance of piezoelectric properties of PVDF and its copolymers and the prediction of their long-term stability in low Earth orbit (LEO) environmental conditions. In this paper, the piezoelectric properties of PVDF and the copolymers formed from polymerization of vinylidene fluoride and trifluoroethylene (TrFE) or hexafluoropropylene (HFP) have been studied over a broad temperature range simulating that expected in LEO. The temperatures experienced by unprotected polymers on low altitude spacecraft have previously been reported as ranging from approximately -100 C to +130 C as the polymer/spacecraft passes in and out of the Earth's shadow. To examine the effects of temperature on the piezoelectric properties of poled PVDF, P(VDF-TrFE) and P(VDF-HFP) the d{sub 33} piezoelectric coefficients and electric displacement-electric field (D-E) hysteresis loops were measured up to 160 C for the d{sub 33} measurements and from -80 to +110 C for the D-E loops. The room temperature d{sub 33} coefficient of PVDF homopolymer films, annealed for extended periods at 50, 80 and 125 C, dropped rapidly within a few days of heating, then remained unchanged for periods of up to 300 days. In contrast, the TrFE copolymer exhibited greater thermal stability than the homopolymer, with the d{sub 33} remaining almost unchanged from the pre-annealing value after heating at 50, 80 and 125 C. The HFP copolymer exhibited poor retention of d33 at temperatures above 80 C. For all three polymers short term annealing at 160 C reduced the d{sub 33} to zero. The decrease in d{sub 33} for the TrFE copolymer was correlated with the change in Curie temperature upon annealing of the copolymer, as observed by differential scanning calorimetry (DSC). Unlike radiation damage, which may occur from vacuum UV and atomic oxygen in LEO, the depoling of the polymers on exposure to elevated temperatures was attributed to a physical randomization of the morphology rather than a chemical degradation process. In situ D-E loop measurements over the temperature range -80 to +110 C showed that the remnant polarization of the TrFE copolymer was more stable than the PVDF homopolymer. These results suggest that the TrFE copolymer appears to have a better overall performance in thermal extremes compared with PVDF or an HFP copolymer.

Abstract not provided.

The γ-irradiated-oxidation of pentacontane (C50H102) and the polymer polyisoprene was investigated as a function of oxidation level using 17O nuclear magnetic resonance (NMR) spectroscopy. It is demonstrated that by using 17O labeled O2 gas during the γ-irradiation process, details about the oxidative degradation mechanisms can be directly obtained from the analysis of the 17O NMR spectra. Production of carboxylic acids is the primary oxygen-containing functionality during the oxidation of pentacontane, while ethers and alcohols are the dominant oxidation product observed for polyisoprene. The formation of ester species during the oxidation process is very minor for both materials, with water also being produced in significant amounts during the radiolytic oxidation of polyisoprene. The ability to focus on the oxidative component of the degradation process using 17O NMR spectroscopy demonstrates the selectivity of this technique over more conventional approaches. © 2001 Elsevier Science Ltd.

Abstract not provided.

Abstract not provided.

A hydroxy-terminated polybutadiene (HTPB)/isophorone diisocyanate (IPDI) elastomer is commonly used as propellant binder material. The thermal degradation of the binder is believed to be an important parameter governing the performance of the propellant. The aging of these binders can be monitored by mechanical property measurements such as modulus or tensile elongation. These techniques, however, are not easily adapted to binder agents that are dispersed throughout a propellant. In this paper the authors investigated solid state NMR relaxation times as a means to predict the mechanical properties of the binder as a function of aging time. {sup 1}H spin-lattice and spin-spin relaxation times were found to be insensitive to the degree of thermal degradation of the elastomer. Apparently these relaxation times depend on localized motions that are only weakly correlated with mechanical properties. A strong correlation was found between the {sup 13}C cross-polarization (CP) NMR time constant, T{sub cp}, and the tensile elongation at break of the elastomer as a function of aging time. A ramped-amplitude CP experiment was shown to be less sensitive to imperfections in setting critical instrumental parameters for this mobile material.

Abstract not provided.

The authors have shown that the hydroperoxide species in {gamma}-irradiated {sup 13}C-polyethylene can be directly observed by {sup 13}C MAS NMR spectroscopy. The experiment was performed without the need for special sample preparation such as chemical derivatization or dissolution. Annealing experiments were employed to study the thermal decomposition of the hydroperoxide species and to measure an activation energy of 98 kJ/mol. EPR spectroscopy suggests that residual polyenyl and alkylperoxy radicals are predominantly trapped in interracial or crystalline regions, while the peroxy radicals observed after UV-photolysis of hydroperoxides are in amorphous regions.

We report an evaporation-induced self-assembly procedure to prepare poly(bridged silsesquioxane) thin-film and particulate mesophases that incorporate organic moieties (1-3) into periodic, mesostructured frameworks as molecularly dispersed bridging ligands. Capacitance-voltage measurements along with a variety of structural characterization procedures were performed to begin to elucidate structure-property relationships of this new class of surfactant-templated mesophases. We observed a consistent trend of increasing modulus and hardness and decreasing dielectric constant with substitution of the bridged silsesquioxane (≡Si-(CH2)2-Si≡) for siloxane (≡Si-O-Si≡) in the framework. This preliminary evidence suggests that the introduction of integral organic groups into the frameworks of mesoporous materials can result in synergistic properties, promising an unprecedented ability to tune properties and function.

Oligomethylhydridosiloxane and tis copolymer with dimethylsiloxane undergo redistribution chemistry with catalytic tetrabutylammonium hydroxide (TBAH) to produce methylsilane and polymethylsilsesquioxanes. The rate and extent of redistribution reaction can be controlled by the amount of TBAH added, as well as use of solvent. The extent reaction can be followed by both infrared radiation (IR) and solid state NMR spectroscopy, following the disappearance of the SiH in the starting oligosiloxane.

Abstract not provided.