Publications

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

The use of Low Temperature Co-Fired Ceramics (LTCC) is a very attractive material option for advanced packaging. For applications, a variety of features are printed in the base material: thermal and electrical vias, resistors, solder pads to name a few. Most of these features have materials that are thermally and elastically mismatched from the LTCC, producing a localized residual stress. These stresses impact the strength and reliability of the LTCC package. Here we present results and analysis for the strength and reliability assessment of an LTCC (DupontTM 951) with and without Au vias. The reliability of the ceramic material is assessed from the perspective of its susceptibility to sub-critical crack growth (SCG). Metallic vias can significantly lower the strength of the LTCC, however, their presence does not change the measured susceptibility of the material to SCG. Using our experimental data, and empirical descriptions of SCG laws, safe design life for LTCC packages under a particular stress state is estimated.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Glasses filled with ceramic or metallic powders have been developed for use as seals for solid oxide fuel cells (SOFC's) as part of the U.S. Department of Energy's Solid State Energy Conversion Alliance (SECA) Program. The composites of glass (alkaline earth-alumina-borate) and powders ({approx}20 vol% of yttria-stabilized zirconia or silver) were shown to form seals with SOFC materials at or below 900 C. The type and amount of powder were adjusted to optimize thermal expansion to match the SOFC materials and viscosity. Wetting studies indicated good wetting was achieved on the micro-scale and reaction studies indicated that the degree of reaction between the filled glasses and SOFC materials, including spinel-coated 441 stainless steel, at 750 C is acceptable. A test rig was developed for measuring strengths of seals cycled between room temperature and typical SOFC operating temperatures. Our measurements showed that many of the 410 SS to 410 SS seals, made using silver-filled glass composites, were hermetic at 0.2 MPa (2 atm.) of pressure and that seals that leaked could be resealed by briefly heating them to 900 C. Seal strength measurements at elevated temperature (up to 950 C), measured using a second apparatus that we developed, indicated that seals maintained 0.02 MPa (0.2 atm.) overpressures for 30 min at 750 C with no leakage. Finally, the volatility of the borate component of sealing glasses under SOFC operational conditions was studied using weight loss measurements and found by extrapolation to be less than 5% for the projected SOFC lifetime.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Cylindrical inhomogeneities are often deliberately incorporated into engineering ceramics (e.g., fibers, vias, electrical feedthroughs). The thermal expansion mismatch between the matrix and inhomogeneity creates a state of localized stress. We show that for radial cracks around such inhomogeneities, there may be conditions of crack stability even in the presence of an external, destabilizing field. This stability, and the nature of the stress intensity factor due to local stresses, modifies the strength distribution of the matrix. A fracture-mechanics approach allows the prediction of the new strength distributions. As an illustration of this approach, calculations for commonly used ceramic-metal inhomogeneity material pairs are discussed. Depending on the inhomogeneity/flaw size ratio, the new strength distributions can have lower or higher strength variability than the matrix. If the inhomogeneity radius (R) is chosen such that a majority of the cracks in the matrix are >0.25R, the material will have the highest possible strength and reduced variability. © 2008 The American Ceramic Society.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

An interdisciplinary team of scientists and engineers having broad expertise in materials processing and properties, materials characterization, and computational mechanics was assembled to develop science-based modeling/simulation technology to design and reproducibly manufacture high performance and reliable, complex microelectronics and microsystems. The team's efforts focused on defining and developing a science-based infrastructure to enable predictive compaction, sintering, stress, and thermomechanical modeling in ''real systems'', including: (1) developing techniques to and determining materials properties and constitutive behavior required for modeling; (2) developing new, improved/updated models and modeling capabilities, (3) ensuring that models are representative of the physical phenomena being simulated; and (4) assessing existing modeling capabilities to identify advances necessary to facilitate the practical application of Sandia's predictive modeling technology.

Instrumented indentation has yielded mixed results when used to measure surface residual stresses in metal films. Relative to metals, many glasses and ceramics have a low modulus-to-yield strength (E/sy) ratio. The advantage of this characteristic for measuring residual stress using instrumented indentation is demonstrated by a series of comparative spherical and conical tip finite element simulations. Two cases are considered: (i) a material with E/s{sub y} = 24-similar to glass and (ii) a material with E/s{sub y} = 120-similar to metal films. In both cases, compressive residual stress shifts the simulated load-displacement response toward increasing hardness, irrespective of tip geometry. This shift is shown to be entirely due to pile up for the ''metal'' case, but primarily due to the direct influence of the residual stress for the ''glass'' case. Hardness changes and load-displacement curve shifts are explained by using the spherical cavity model. Supporting experimental results on stressed glasses are provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

HfB{sub 2} and ZrB{sub 2} are of interest for thermal protection materials because of favorable thermal stability, mechanical properties, and oxidation resistance. We have made dense diboride ceramics with 2 to 20 % SiC by hot pressing at 2000 C and 5000 psi. High-resolution transmission electron microscopy (TEM) shows very thin grain boundary phases that suggest liquid phase sintering. Fracture toughness measurements give RT values of 4 to 6 MPam{sup 1/2}. Four-pt flexure strengths measured in air up to 1450 C were as high as 450-500 MPa. Thermal diffusivities were measured to 2000 C for ZrB{sub 2} and HfB{sub 2} ceramics with SiC contents from 2 to 20%. Thermal conductivities were calculated from thermal diffusivities and measured heat capacities. Thermal diffusivities were modeled using different two-phase composite models. These materials exhibit excellent high temperature properties and are attractive for further development for thermal protection systems.

Abstract not provided.