Publications

Using intense magnetic pressure, a method was developed to launch flyer plates to velocities in excess of 20 km/s. This technique was used to perform plate-impact, shock wave experiments on cryogenic liquid deuterium (LD{sub 2}) to examine its high-pressure equation of state (EOS). Using an impedance matching method, Hugoniot measurements were obtained in the pressure range of 30-70 GPa. The results of these experiments disagree with previously reported Hugoniot measurements of LD{sub 2} in the pressure range above {approx}40 GPa, but are in good agreement with first principles, ab-initio models for hydrogen and its isotopes.

Recently an innovative technique known as the Isentropic Compression Experiment (ICE) was developed that allows the dynamic compressibility curve of a material to be measured in a single experiment. Hence, ICE significantly reduces the cost and time required for generating and validating theoretical models of dynamic material response. ICE has been successfully demonstrated on several materials using the 20 MA Z accelerator, resulting in a large demand for its use. The present project has demonstrated its use on another accelerator, Saturn. In the course of this study, Saturn was tailored to produce a satisfactory drive time structure, and instrumented to produce velocity data. Pressure limits are observed to be approximately 10-15 GPa (''LP'' configuration) or 40-50 GPa (''HP'' configuration), depending on sample material. Drive reproducibility (panel to panel within a shot and between shots) is adequate for useful experimentation, but alignment fixturing problems make it difficult to achieve the same precision as is possible at Z. Other highlights included the useful comparison of slightly different PZT and ALOX compositions (neutron generator materials), temperature measurement using optical pyrometry, and the development of a new technique for preheating samples. 28 ICE tests have been conducted at Saturn to date, including the experiments described herein.

Sandia is investigating the shock response of single-crystal diamond up to several Mbar pressure in a collaborative effort with the Institute for Shock Physics (ISP) at Washington State University (WSU). This is project intended to determine (i) the usefulness of diamond as a window material for high pressure velocity interferometry measurements, (ii) the maximum stress level at which diamond remains transparent in the visible region, (iii) if a two-wave structure can be detected and analyzed, and if so, (iv) the Hugoniot elastic limit (HEL) for the [110] orientation of diamond. To this end experiments have been designed and performed, scoping the shock response in diamond in the 2-3 Mbar pressure range using conventional velocity interferometry techniques (conventional VISAR diagnostic). In order to perform more detailed and highly resolved measurements, an improved line-imaging VISAR has been developed and experiments using this technique have been designed. Prior to performing these more detailed experiments, additional scoping experiments are being performed using conventional techniques at WSU to refine the experimental design.

In order to provide real-time data for validation of three dimensional numerical simulations of heterogeneous materials subjected to impact loading, an optically recording velocity interferometer system (ORVIS) has been adapted to a line-imaging instrument capable of generating precise mesoscopic scale measurements of spatially resolved velocity variations during dynamic deformation. Combining independently variable target magnification and interferometer fringe spacing, this instrument can probe a velocity field along line segments up to 15 mm in length. In high magnification operation, spatial resolution better than 10 {micro}m can be achieved. For events appropriate to short recording times, streak camera recording can provide temporal resolution better than 0.2 ns. A robust method for extracting spatially resolved velocity-time profiles from streak camera image data has been developed and incorporated into a computer program that utilizes a standard VISAR analysis platform. The use of line-imaging ORVIS to obtain measurements of the mesoscopic scale dynamic response of shocked samples has been demonstrated on several different classes of heterogeneous materials. Studies have focused on pressed, granular sugar as a simulant material for the widely used explosive HMX. For low-density (65% theoretical maximum density) pressings of sugar, material response has been investigated as a function of both impact velocity and changes in particle size distribution. The experimental results provide a consistent picture of the dispersive nature of the wave transmitted through these samples and reveal both transverse and longitudinal wave structures on mesoscopic scales. This observed behavior is consistent with the highly structured mesoscopic response predicted by 3-D simulations. Preliminary line-imaging ORVIS measurements on HMX as well as other heterogeneous materials such as foam and glass-reinforced polyester are also discussed.

Abstract not provided.