Pulse-burst particle image velocimetry has been used to acquire time-resolved data at 37.5 kHz of the flow over a finite-width rectangular cavity at Mach 0.8. Power spectra of the particle image velocimetry data reveal four resonance modes that match the frequencies detected simultaneously using high-frequency wall pressure sensors, but whose magnitudes exhibit spatial dependence throughout the cavity. Spatiotemporal cross correlations of velocity to pressure were calculated after bandpass filtering for specific resonance frequencies. Cross-correlation magnitudes express the distribution of resonance energy, revealing local maxima and minima at the edges of the shear layer attributable to wave interference between downstream-and upstream-propagating disturbances. Turbulence intensities were calculated using a triple decomposition and are greatest in the core of the shear layer for higher modes, where resonant energies ordinarily are lower. Most of the energy for the lowest mode lies in the recirculation region and results principally from turbulence rather than resonance. Together, the velocity-pressure cross correlations and the triple-decomposition turbulence intensities explain the sources of energy identified in the spatial distributions of power spectra amplitudes.
The resonance modes in Mach 0.94 turbulent flow over a cavity having a length-to-depth ratio of five were explored using time-resolved particle image velocimetry and time-resolved pressure sensitive paint. Mode-switching occurred in the velocity field simultaneous with the pressure field. The first cavity mode corresponded to large-scale motions in shear layer and in the vicinity of the recirculation region, whereas the second and third modes contained organized structures associated with shear layer vortices. Modal surface pressures exhibited streamwise periodicity generated by the interference of downstream-traveling disturbances in shear layer with upstream-traveling acoustical waves. Because of this interference, the modal velocity fields also exhibited local maxima at locations containing pressure minima and vice-versa. Modal convective (phase) velocities, based on cross-correlations of bandpass-filtered velocity fields, decreased with decreasing mode number as the modal activity resided in lower portions of the cavity. These phase velocities also exhibited streamwise periodicity caused by wave interference. The measurements demonstrate that despite the complexities inherent in compressible cavity flows, many of the most prevalent resonance dynamics can be described with simple acoustical analogies.
Boundary-layer transition was measured on a pitched, 7° half-angle cone in a Mach 8 conventional wind tunnel. On a smooth cone, transition via second-mode waves was ob- served at all angles of attack. In addition, naturally-excited stationary crossow waves were apparent in temperature sensitive paint images, but did not appear to lead to transition. Two patterns of roughness elements were used to generate higher-amplitude stationary crossow waves. Breakdown of the stationary waves was observed. The roughness resulted in instability amplitudes nearly an order of magnitude larger than the smooth cone at the same Reynolds numbers and higher instability growth rates. Transition occurred 30% - 40% sooner using the roughness elements with peak amplitudes near 15 - 20%, for α ≥ 4°. A low-frequency, coherent wave was measured at all angles of attack. The calculated phase velocity shows a strong dependence on angle of attack, but the propagation angle is similar for all non-zero α. The measured wave properties are curiously similar to measurements of a suspected tunnel-noise-driven instability made on an elliptic cone at Mach 6.
we studied the influence of compressibility on the shear layer over a rectangular cavity of variable width in a free stream Mach number range of 0.6–2.5 using particle image velocimetry data in the streamwise centre plane. As the Mach number increases, the vertical component of the turbulence intensity diminishes modestly in the widest cavity, but the two narrower cavities show a more substantial drop in all three components as well as the turbulent shear stress. Furthermore, this contrasts with canonical free shear layers, which show significant reductions in only the vertical component and the turbulent shear stress due to compressibility. The vorticity thickness of the cavity shear layer grows rapidly as it initially develops, then transitions to a slower growth rate once its instability saturates. When normalized by their estimated incompressible values, the growth rates prior to saturation display the classic compressibility effect of suppression as the convective Mach number rises, in excellent agreement with comparable free shear layer data. The specific trend of the reduction in growth rate due to compressibility is modified by the cavity width.
Fluid-structure interactions were studied on a 7 * half-angle cone in the Sandia Hypersonic Wind Tunnel at Mach 8 over a range of freestream Reynolds numbers b etween 3 . 3 and 14 . 5 x 10 6 / m . A thin panel with tunable structural natural frequencies was integrated into the cone and exposed to naturally developing boundary layers. An elevated panel re sponse was measured during boundary- layer transition at frequencies corresponding to the turbu lent burst rate, and lower vibrations were measured under a turbulent boundary layer. Controlled pert urbations from an electrical discharge were then introduced into the boundary layer at varying freq uencies corresponding to the struc- tural natural frequencies of the panel. The perturbations w ere not strong enough to drive a panel response exceeding that due to natural transition. Instead at high repetition rates, the perturber modified the turbulent burst rate and intermittency on the co ne and therefore changed the condi- tions for when an elevated transitional panel vibration res ponse occurred. Studies were also conducted in the Boeing/AFOSR Mach 6 Quiet Tunnel at Purdue University. Under quiet flow, natural transition does not occur, and the c ontrolled perturbations are the only disturbance source. A clear panel response to turbulent spo ts created by the controlled pertur- bations was observed at varying frequencies of spot generat ion. The quiet-flow measurements confirm the clear relationship between turbulent spot passa ge and panel vibration.
Fluid–structure interactions that occur during aircraft internal store carriage were experimentally explored at Mach 0.58–1.47 using a generic, aerodynamic store installed in a rectangular cavity having a length-to-depth ratio of seven. The store vibrated in response to the cavity flow at its natural structural frequencies, and it exhibited a directionally dependent response to cavity resonance frequencies. Cavity tones excited the store in the streamwise and wall-normal directions consistently, whereas the spanwise response to cavity tones was much more limited. Increased surface area associated with tail fins raised vibration levels. The store had interchangeable components to vary its natural frequencies by about 10–300 Hz. By tuning natural frequencies, mode-matched cases were explored where a prominent cavity tone frequency matched a structural natural frequency of the store. Mode matching in the streamwise and wall-normal directions produced substantial increases in peak store vibrations, though the response of the store remained linear with dynamic pressure. Near mode-matched frequencies, changes in cavity tone frequencies of only 1% altered store peak vibrations by as much as a factor of two. In conclusion, mode matching in the spanwise direction did little to increase vibrations.
Riley, Zachary B.; Deshmukh, Rohit; Miller, Brent A.; McNamara, Jack J.; Casper, Katya M.
The inherent relationship between boundary-layer stability, aerodynamic heating, and surface conditions makes the potential for interaction between the structural response and boundary-layer transition an important and challenging area of study in high-speed flows. This paper phenomenologically explores this interaction using a fundamental two-dimensional aerothermoelastic model under the assumption of an aluminum panel with simple supports. Specifically, an existing model is extended to examine the impact of transition onset location, transition length, and transitional overshoot in heat flux and fluctuating pressure on the structural response of surface panels. Transitional flow conditions are found to yield significantly increased thermal gradients, and they can result in higher maximumpanel temperatures compared to turbulent flow. Results indicate that overshoot in heat flux and fluctuating pressure reduces the flutter onset time and increases the strain energy accumulated in the panel. Furthermore, overshoot occurring near the midchord can yield average temperatures and peak displacements exceeding those experienced by the panel subject to turbulent flow. These results suggest that fully turbulent flow does not always conservatively predict the thermo-structural response of surface panels.
Fluid-structure interactions were studied on a 7° half-angle cone in the Sandia Hypersonic Wind Tunnel at Mach 8 over a range of freestream Reynolds numbers between 3.3 and 14.5 × 106/m. A thin panel with tunable structural natural frequencies was integrated into the cone and exposed to naturally developing boundary layers. An elevated panel response was measured during boundary-layer transition at frequencies corresponding to the turbulent burst rate, and lower vibrations were measured under a turbulent boundary layer. Controlled perturbations from an electrical discharge were then introduced into the boundary layer at varying frequencies corresponding to the structural natural frequencies of the panel. The perturbations were not strong enough to drive a panel response exceeding that due to natural transition. Instead at high repetition rates, the perturber modified the turbulent burst rate and intermittency on the cone and therefore changed the conditions for when an elevated transitional panel vibration response occurred.
Fluid-structure interactions that occur during aircraft internal store carriage were experimentally explored at Mach 0.58-1.47 using a generic, aerodynamic store installed in a rectangular cavity having a length-To-depth ratio of seven. The store vibrated in response to the cavity flow at its natural structural frequencies, and it exhibited a directionally dependent response to cavity resonance frequencies. Cavity tones excited the store in the streamwise and wall-normal directions consistently, whereas the spanwise response to cavity tones was much more limited. Increased surface area associated with tail fins raised vibration levels. The store had interchangeable components to vary its natural frequencies by about 10-300 Hz. By tuning natural frequencies, mode-matched cases were explored where a prominent cavity tone frequency matched a structural natural frequency of the store. Mode matching in the streamwise and wall-normal directions produced substantial increases in peak store vibrations, though the response of the store remained linear with dynamic pressure. Near mode-matched frequencies, changes in cavity tone frequencies of only 1% altered store peak vibrations by as much as a factor of two. Mode matching in the spanwise direction did little to increase vibrations.
Time-resolved particle image velocimetry (TR-PIV) measurements were made in a shock tube using a pulse-burst laser. Two transient flowfields were investigated including the baseline flow in the empty shock tube and the wake growth downstream of a cylinder spanning the width of the test section. Boundary layer growth was observed following the passage of the incident shock in the baseline flow, while the core flow velocity increased with time. The measured core flow acceleration was compared to that predicted using a classical unsteady boundary layer growth model. The model typically provided good estimates of core flow acceleration at early times, but then typically underestimated the acceleration. As a result of wall boundary layers, a significant amount of spatial non-uniformity remained in the flow following the passage of the end-wall reflected shock, which could be an important factor in combustion chemistry experiments. In the transient wake growth measurements, the wake downstream of the cylinder was symmetric immediately following the passage of the incident shock. At later times (≈ 0.5 ms), the wake transitioned to a von Kármán vortex street. The TR-PIV data were bandpass filtered about the vortex shedding frequency to reveal additional details on the transient wake growth.
Mach 0.94 flow over a cavity having a length-to-depth ratio of five was explored using time-resolved particle image velocimetry (TR-PIV) with a burst-mode laser. The data were used to probe the resonance dynamics of the first three cavity (Rossiter) tones. Bandpass filtering was employed to reveal the coherent flow structure associated with each tone. The first Rossiter mode was associated with a propagation of large scale structures in the recirculation region, while the second and third modes contained organized structures consistent with convecting vortical disturbances. The wavelengths of the second and third modes were quite similar to those observed in a previous study by the current authors using phase-averaged PIV. Convective velocities computed using cross correlations in the unfiltered data showed the convective velocity increased with streamwise distance in a fashion similar to other studies. Convective velocities during cavity resonance were found to decrease with decreasing mode number, consistent with the modal activity residing in lower portions of the cavity in regions of lower local mean velocities. The convective velocity fields associated with resonance exhibited a streamwise periodicity consistent with wall-normal undulations in the resonant velocity fields; however, additional work is required to confirm this is not an analysis artifact.
The flow over an aircraft bay is often represented using a rectangular cavity; however, this simplification neglects many features of actual flight geometry that could affect the unsteady pressure field and resulting loading in the bay. To address this shortcoming, a complex cavity geometry was developed to incorporate more realistic aircraft-bay features including shaped inlets, internal cavity structure, and doors. A parametric study of these features was conducted based on fluctuating pressure measurements at subsonic and supersonic Mach numbers. Resonance frequencies and amplitudes increased in the complex geometry compared to a simple rectangular cavity that could produce severe loading conditions for store carriage. High-frequency content and dominant frequencies were generated by features that constricted the flow such as leading-edge overhangs, internal cavity variations, and the presence of closed doors. Broadband frequency components measured at the aft wall of the complex cavities were also significantly higher than in the rectangular geometry. Furthermore, these changes highlight the need to consider complex geometric effects when predicting the flight loading of aircraft bays.
Experiments were performed to understand the complex fluid-structure interactions that occur during aircraft internal store carriage. A cylindrical store was installed in a rectangular cavity having a length-to-depth ratio of 3.33 and a length-to-width ratio of 1. The Mach number ranged from 0.6 to 2.5 and the incoming boundary layer was turbulent. Fast-response pressure measurements provided aeroacoustic loading in the cavity, while triaxial accelerometers provided simultaneous store response. Despite occupying only 6% of the cavity volume, the store significantly altered the cavity acoustics. The store responded to the cavity flow at its natural structural frequencies, and it exhibited a directionally dependent response to cavity resonance. Specifically, cavity tones excited the store in the streamwise and wall-normal directions consistently, whereas a spanwise response was observed only occasionally. The streamwise and wall-normal responses were attributed to the longitudinal pressure waves and shear layer vortices known to occur during cavity resonance. Although the spanwise response to cavity tones was limited, broadband pressure fluctuations resulted in significant spanwise accelerations at store natural frequencies. The largest vibrations occurred when a cavity tone matched a structural natural frequency, although energy was transferred more efficiently to natural frequencies having predominantly streamwise and wall-normal motions.
The flow over an open aircraft bay is often represented in a wind tunnel with a cavity. In flight, this flow is unconfined, though in experiments, the cavity is surrounded by wind tunnel walls. If untreated, wind tunnel wall effects can lead to significant distortions of cavity acoustics in subsonic flows. To understand and mitigate these cavity–tunnel interactions, a parametric approach was taken for flow over an L/D = 7 cavity at Mach numbers 0.6–0.8. With solid tunnel walls, a dominant cavity tone was observed, likely due to an interaction with a tunnel duct mode. An acoustic liner opposite the cavity decreased the amplitude of the dominant mode and its harmonics, a result observed by previous researchers. Acoustic dampeners were also placed in the tunnel sidewalls, which further decreased the dominant mode amplitudes and peak amplitudes associated with nonlinear interactions between cavity modes. This indicates that cavity resonance can be altered by tunnel sidewalls and that spanwise coupling should be addressed when conducting subsonic cavity experiments. Though mechanisms for dominant modes and nonlinear interactions likely exist in unconfined cavity flows, these effects can be amplified by the wind tunnel walls.
Sandia’s Hypersonic Wind Tunnel (HWT) became operational in 1962, providing a test capability for the nation’s nuclear weapons complex. The first modernization program was completed in 1977. A blowdown facility with a 0.46-m diameter test section, the HWT operates at Mach 5, 8, and 14 with stagnation pressures to 21 MPa and temperatures to 1400K. Minimal further alteration to the facility occurred until 2008, but in recent years the HWT has received considerable investment to ensure its viability for at least the next 25 years. This has included reconditioning of the vacuum spheres, replacement of the high-pressure air tanks for Mach 5, new compressors to provide the high-pressure air, upgrades to the cryogenic nitrogen source for Mach 8 and 14, an efficient high-pressure water cooling system for the nozzle throats, and refurbishment of the electric-resistance heaters. The HWT is now returning to operation following the largest of the modernization projects, in which the old variable transformer for the 3-MW electrical system powering the heaters was replaced with a silicon-controlled rectifier power system. The final planned upgrade is a complete redesign of the control console and much of the gas-handling equipment.
Particle image velocimetry (PIV) measurements quantified the coherent structure of acoustic tones in a Mach 0.91 cavity flow. Stereoscopic PIV measurements were performed at 10-Hz and two-component, time-resolved data were obtained using a pulse-burst laser. The cavity had a square planform, a length-to-depth ratio of five, and an incoming turbulent boundary layer. Simultaneous fast-response pressure signals were bandpass filtered about each cavity tone frequency. The 10-Hz PIV data were then phase-averaged according to the bandpassed pressures to reveal the flow structure associated with the resonant tones. The first Rossiter mode was associated with large scale oscillations in the shear layer, while the second and third modes contained organized structures consistent with convecting vortical disturbances. The spatial wavelengths of the cavity tones, based on the vertical coherent velocity fields, were less than those predicted by the Rossiter relation. With increasing streamwise distance the spacing between structures increased and approached the predicted Rossiter value at the aft-end of the cavity. Moreover, the coherent structures appeared to rise vertically with downstream propagation. The time-resolved PIV data were bandpass filtered about the cavity tone frequencies to reveal flow structure. The resulting spacing between disturbances was similar to that in the phase-averaged flowfields.
To investigate the pressure-fluctuation field beneath turbulent spots in a hypersonic boundary layer, a study was conducted on the nozzle wall of the Boeing/AFOSR Mach-6 Quiet Tunnel. Controlled disturbances were created by pulsed-glow perturbations based on the electrical breakdown of air. Under quiet-flow conditions, the nozzle-wall boundary layer remains laminar and grows very thick over the long nozzle length. This allows the development of large disturbances that can be well-resolved with high-frequency pressure transducers. A disturbance first grows into a second-mode instability wavepacket that is concentrated near its own centreline. Weaker disturbances are seen spreading from the centre. The waves grow and become nonlinear before breaking down to turbulence. The breakdown begins in the core of the packets where the wave amplitudes are largest. Second-mode waves are still evident in front of and behind the breakdown point and can be seen propagating in the spanwise direction. The turbulent core grows downstream, resulting in a spot with a classical arrowhead shape. Behind the spot, a low-pressure calmed region develops. However, the spot is not merely a localized patch of turbulence; instability waves remain an integral part. Limited measurements of naturally occurring disturbances show many similar characteristics. From the controlled disturbance measurements, the convection velocity, spanwise spreading angle, and typical pressure-fluctuation field were obtained.
Experiments were conducted at freestream Mach numbers of 0.55, 0.80, and 0.90 in open cavity flows having a length-to-depth ratio L/D of 5 and an incoming turbulent boundary having a thickness of about 0.5D. To ascertain aspect ratio effects, the length-to-width ratio L/W was varied between 1.00, 1.67, and 5.00. Two stereoscopic PIV systems were used simultaneously to characterize the flow in the plane at the spanwise center of the cavity. For each aspect ratio, trends in the mean and turbulence fields were identified, regardless of Mach number. The recirculation region had the weakest reverse velocities in the L/W = 1.67 cavity, a trend previously observed at supersonic Mach numbers. Also, like the previous supersonic experiments, the L/W = 1.00 and L/W = 5.00 mean streamwise velocities were similar. The L/W = 1.00 cavity flows had the highest turbulence intensities, whereas the two narrower cavities exhibited lower turbulence intensities of a comparable level. This is in contrast to previous supersonic experiments, which showed the lowest turbulence levels in the L/W = 1.67 cavity.
High-frequency pressure sensors were used in conjunction with a high-speed schlieren system to study the growth and breakdown of boundary-layer disturbances into turbulent spots on a 7° cone in the Sandia Hypersonic Wind Tunnel at Mach 5 and 8. To relate the intermittent disturbances to the average characteristics of transition on the cone, the statistical distribution of these disturbances must be known. These include the boundarylayer intermittency, burst rate, and average disturbance length. Traditional low-speed methods to characterize intermittency identify only turbulent/nonturbulent regions. However at high M, instability waves become an important part of the transitional region. Algorithms to distinguish instability waves from turbulence in both the pressure and schlieren measurements are being developed and the corresponding intermittency, burst rate, and average burst length of both regions have been provisionally computed for several cases at Mach 5 and 8. Distinguishing instability waves from turbulence gives a better description of the intermittent boundary layer at high M and will allow the fluctuations associated with boundary-layer instabilities to be incorporated into transitional models.