Dipicolinic acid (DPA, 2,6-pyridinedicarboxylic acid) is a substance uniquely present in bacterial spores such as that from anthrax (B. anthracis). It is known that DPA can be detected by the long-lived fluorescence of its terbium chelate; the best limit of detection (LOD) reported thus far using a large benchtop gated fluorescence instrument using a pulsed Xe lamp is 2 nM. We use a novel AlGaN light-emitting diode (LED) fabricated on a sapphire substrate that has peak emission at 291 nm. Although the overlap of the emission band of this LED with the absorption band of Tb-DPA ({lambda}{sub max} doublet: 273, 279 nm) is not ideal, we demonstrate that a compact detector based on this LED and an off-the-shelf gated photodetection module can provide an LOD of 0.4 nM, thus providing a basis for convenient early warning detectors.
The goal of this one year LDRD was to improve the overall efficiency of InGaN LEDs by improving the extraction of light from the semiconductor chip. InGaN LEDs are currently the most promising technology for producing high efficiency blue and green semiconductor light emitters. Improving the efficiency of InGaN LEDs will enable a more rapid adoption of semiconductor based lighting. In this LDRD, we proposed to develop photonic structures to improve light extraction from nitride-based light emitting diodes (LEDs). While many advanced device geometries were considered for this work, we focused on the use of a photonic crystal for improved light extraction. Although resonant cavity LEDs and other advanced structures certainly have the potential to improve light extraction, the photonic crystal approach showed the most promise in the early stages of this short program. The photonic crystal (PX)-LED developed here incorporates a two dimensional photonic crystal, or photonic lattice, into a nitride-based LED. The dimensions of the photonic crystal are selected such that there are very few or no optical modes in the plane of the LED ('lateral' modes). This will reduce or eliminate any radiation in the lateral direction so that the majority of the LED radiation will be in vertical modes that escape the semiconductor, which will improve the light-extraction efficiency. PX-LEDs were fabricated using a range of hole diameters and lattice constants and compared to control LEDs without a photonic crystal. The far field patterns from the PX-LEDs were dramatically modified by the presence of the photonic crystal. An increase in LED brightness of 1.75X was observed for light measured into a 40 degree emission cone with a total increase in power of 1.5X for an unencapsulated LED.
Materials studies of high Al-content (> 30%) AlGaN epilayers and the performance of AlGaN-based LEDs with emission wavelengths shorter than 300 nm are reported. N-type AlGaN films with Al compositions greater than 30% reveal a reduction in conductivity with increasing Al composition. The reduction of threading dislocation density from the 1-5 x10{sup 10} cm{sup -2} range to the 6-9 x 10{sup 9}cm{sup -2} range results in an improvement of electrical conductivity and Al{sub 0.90}Ga{sub 0.10}N films with n= 1.6e17 cm-3 and f{acute Y}=20 cm2/Vs have been achieved. The design, fabrication and packaging of flip-chip bonded deep UV LEDs is described. Large area (1 mm x 1 mm) LED structures with interdigitated contacts demonstrate output powers of 2.25 mW at 297 nm and 1.3 mW at 276 nm when operated under DC current. 300 f{acute Y}m x 300 f{acute Y}m LEDs emitting at 295 nm and operated at 20 mA DC have demonstrated less than 50% drop in output power after more than 2400 hours of operation. Optimization of the electron block layer in 274 nm LED structures has enabled a significant reduction in deep level emission bands, and a peak quantum well to deep level ratio of 700:1 has been achieved for 300 f{acute Y}m x 300 f{acute Y}m LEDs operated at 100 mA DC. Shorter wavelength LED designs are described, and LEDs emitting at 260 nm, 254nm and 237 nm are reported.
Ohmic contacts on p-type GaN utilizing Pd/Ir/Au metallization were fabricated and characterized. Metallized samples that were rapid thermally annealed at 400 C for 1 min exhibited linear current-voltage characteristics. Specific ohmic contact resistivities as low as 2 x 10{sup -5} {Omega} cm{sup 2} were achieved. Auger electron spectroscopy and x-ray photoelectron spectroscopy depth profiles of annealed Pd/Ir/Au contact revealed the formation of Pd- and Ir-related alloys at the metal-semiconductor junction with the creation of Ga vacancies below the contact. The excellent contact resistance obtained is attributed to the formation of these Ga vacancies which resulted in the reduction of the depletion region width at the junction.
The junction temperature of AlGaN/GaN ultraviolet (UV) Light-Emitting Diodes (LEDs) emitting at 295 nm is measured by using the temperature coefficients of the diode forward volt-age and emission peak energy. The high-energy slope of the spectrum is explored to measure the carrier temperature. A linear relation between junction temperature and current is found. Analysis of the experimental methods reveals that the diode-forward voltage is the most accurate method (,,b 3 ,,aC). A theoretical model for the dependence of the diode junction voltage (Vj) on junction temperature (T) is developed that takes into account the temperature dependence of the energy gap. A thermal resistance of 87.6 K/W is obtained with the AlGaN/GaN LED sample mounted with thermal paste on a heat sink.
The junction temperature of AlGaN ultraviolet light-emitting diodes emitting at 295 nm is measured by using the temperature coefficients of the diode forward voltage and emission peak energy. The high-energy slope of the spectrum is explored to measure the carrier temperature. A linear relation between junction temperature and current is found. Analysis of the experimental methods reveals that the diode-forward voltage is the most accurate ({+-}3 C). A theoretical model for the dependence of the diode forward voltage (V{sub f}) on junction temperature (T{sub j}) is developed that takes into account the temperature dependence of the energy gap. A thermal resistance of 87.6 K/W is obtained with the device mounted with thermal paste on a heat sink.
Solid-state light sources emitting at wavelengths less than 300 nm would enable technological advances in many areas such as fluorescence-based biological agent detection, non-line-of-sight communications, water purification, and industrial processing including ink drying and epoxy curing. In this paper, we present our recent progress in the development of LEDs with emission between 237 and 297 nm. We will discuss growth and design issues of deep-UV LEDs, including transport in Si-doped AlGaN layers. The LEDs are designed for bottom emission so that improved heat sinking and light extraction can be achieved by flip chipping. To date, we have demonstrated 2.25 mW of output power at 295 nm from 1 mm x 1 mm LEDs operated at 500 mA. Shorter wavelength LEDs emitting at 276 nm have achieved an output power of 1.3 mW at 400 mA. The heterostructure designs that we have employed have suppressed deep level emission to intensities that are up to 330 x lower than the primary quantum well emission.
This SAND report is the final report on Sandia's Grand Challenge LDRD Project 27328, 'A Revolution in Lighting -- Building the Science and Technology Base for Ultra-Efficient Solid-state Lighting.' This project, which for brevity we refer to as the SSL GCLDRD, is considered one of Sandia's most successful GCLDRDs. As a result, this report reviews not only technical highlights, but also the genesis of the idea for Solid-state Lighting (SSL), the initiation of the SSL GCLDRD, and the goals, scope, success metrics, and evolution of the SSL GCLDRD over the course of its life. One way in which the SSL GCLDRD was different from other GCLDRDs was that it coincided with a larger effort by the SSL community - primarily industrial companies investing in SSL, but also universities, trade organizations, and other Department of Energy (DOE) national laboratories - to support a national initiative in SSL R&D. Sandia was a major player in publicizing the tremendous energy savings potential of SSL, and in helping to develop, unify and support community consensus for such an initiative. Hence, our activities in this area, discussed in Chapter 6, were substantial: white papers; SSL technology workshops and roadmaps; support for the Optoelectronics Industry Development Association (OIDA), DOE and Senator Bingaman's office; extensive public relations and media activities; and a worldwide SSL community website. Many science and technology advances and breakthroughs were also enabled under this GCLDRD, resulting in: 55 publications; 124 presentations; 10 book chapters and reports; 5 U.S. patent applications including 1 already issued; and 14 patent disclosures not yet applied for. Twenty-six invited talks were given, at prestigious venues such as the American Physical Society Meeting, the Materials Research Society Meeting, the AVS International Symposium, and the Electrochemical Society Meeting. This report contains a summary of these science and technology advances and breakthroughs, with Chapters 1-5 devoted to the five technical task areas: 1 Fundamental Materials Physics; 2 111-Nitride Growth Chemistry and Substrate Physics; 3 111-Nitride MOCVD Reactor Design and In-Situ Monitoring; 4 Advanced Light-Emitting Devices; and 5 Phosphors and Encapsulants. Chapter 7 (Appendix A) contains a listing of publications, presentations, and patents. Finally, the SSL GCLDRD resulted in numerous actual and pending follow-on programs for Sandia, including multiple grants from DOE and the Defense Advanced Research Projects Agency (DARPA), and Cooperative Research and Development Agreements (CRADAs) with SSL companies. Many of these follow-on programs arose out of contacts developed through our External Advisory Committee (EAC). In h s and other ways, the EAC played a very important role. Chapter 8 (Appendix B) contains the full (unedited) text of the EAC reviews that were held periodically during the course of the project.