Thin tellurium (Te) has been predicted as a potential two dimensional system exhibiting superior thermoelectric and electrical properties. Here, we report the synthesis of high quality ultrathin Te nanostructures and the study of their electrical properties at room temperature. High quality ultrathin Te nanostructures are obtained by high temperature vapor phase deposition on c-plane sapphire substrates. The obtained nanostructures are as thin as 3 nm and exhibit α-Te phase with trigonal crystal structure. Room temperature electrical measurements show significantly higher electrical conductivity compared to prior reports of Te in bulk form or in nanostructure form synthesized by low temperature vapor deposition or wet chemical methods. Additionally, these nanostructures exhibit high field effect hole mobility comparable to black-phosphorous measured previously under similar conditions.
The room temperature electronic transport properties of 1 μm thick Bi0.4Sb1.6Te3 (BST) films correlate with overall microstructural quality. Films with homogeneous composition are deposited onto fused silica substrates, capped with SiN to prevent both oxidation and Te loss, and postannealed to temperatures ranging from 200 to 450 °C. BST grain sizes and (00l) orientations improve dramatically with annealing to 375 °C, with smaller increases to 450 °C. Tiny few-nanometer-sized voids in the as-deposited film grain boundaries coalesce into larger void sizes up to 300 nm with annealing to 350 °C; the smallest voids continue coalescing with annealing to 450 °C. These voids are decorated with few-nanometer-sized Sb clusters that increase in number with increasing annealing temperatures, reducing the Sb content of the remaining BST film matrix. Resistivity decreases linearly with increasing temperature over the entire range studied, consistent with improving crystalline quality. The Seebeck coefficient also improves with crystalline quality to 350 °C, above which void coalescence and reduced Sb content from the BST matrix correlate with a decrease in the Seebeck coefficient. Nevertheless, a plateau exists for an optimal power factor between 350 and 450 °C, implying thermal stability to higher temperatures than previously reported.
Harris, Zachary D.; Lawrence, Samantha K.; Medlin, Douglas L.; Guetard, Gael; Burns, James T.; Somerday, Brian P.
Uniaxial mechanical testing conducted at room temperature (RT) and 77 K on hydrogen (H)-exposed nickel was coupled with targeted microscopy to evaluate the influence of deformation temperature, and therefore mobile H-deformation interactions, on intergranular cracking in nickel. Results from interrupted tensile tests conducted at cryogenic temperatures (77 K), where mobile H-deformation interactions are effectively precluded, and RT, where mobile H-deformation interactions are active, indicate that mobile H-deformation interactions are not an intrinsic requirement for H-induced intergranular fracture. Moreover, an evaluation of the true strain for intergranular microcrack initiation for testing conducted at RT and 77 K suggests that H which is segregated to grain boundaries prior to the onset of straining dominates the H-induced fracture process for the prescribed H concentration of 4000 appm. Finally, recent experiments suggesting that H-induced fracture is predominately driven by mobile H-deformation interactions, as well as the increased susceptibility of coherent twin boundaries to H-induced crack initiation, are re-examined in light of these new results.
V-telluride superlattice thin films have shown promising performance for on-chip cooling devices. Recent experimental studies have indicated that device performance is limited by the metal/semiconductor electrical contacts. One challenge in realizing a low resistivity contact is the absence of fundamental knowledge of the physical and chemical properties of interfaces between metal and V-telluride materials. This study presents a combination of experimental and theoretical efforts to understand, design, and harness low resistivity contacts to V-tellurides. Ab initio calculations are used to explore the effects of interfacial structure and chemical compositions on the electrical contacts, and an ab initio based macroscopic model is employed to predict the fundamental limit of contact resistivity as a function of both carrier concentration and temperature. Under the guidance of theoretical studies, an experimental approach is developed to fabricate low resistivity metal contacts to V-telluride thin film superlattices, achieving a 100-fold reduction compared to previous work. Interfacial characterization and analysis using both scanning transmission electron microscopy and energy-dispersive X-ray spectroscopy show unusual interfacial morphology and the potential for further improvement in contact resistivity. Finally, the improved contacts are harnessed to realize an improved high-performance thermoelectric cooling module.