Publications

Abstract not provided.

Additive Manufacturing (AM) can create novel and complex engineered material structures. Features such as controlled porosity, micro-fibers and/or nano-particles, transitions in materials and integral robust coatings can be important in developing solutions for fusion subcomponents. A realistic understanding of this capability would be particularly valuable in identifying development paths. Major concerns for using AM processes with lasers or electron beams that melt powder to make refractory parts are the power required and residual stresses arising in fabrication. A related issue is the required combination of lasers or e-beams to continue heating of deposited material (to reduce stresses) and to deposit new material at a reasonable built rate while providing adequate surface finish and resolution for meso-scale features. Some Direct Write processes that can make suitable preforms and be cured to an acceptable density may offer another approach for PFCs.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

We present measurements and modeling of aluminum erosion and redeposition experiments in separate helium and deuterium low power, low density L-mode plasmas at the outer divertor strike point of DIII-D to provide a low-Z material benchmark dataset for tokamak erosion-deposition modeling codes. Coatings of Al ∼100 nm thick were applied to ideal (smooth) and realistic (rough) surfaces and exposed to repeat plasma discharges using the DiMES probe. Redeposition in all cases was primarily in the downstream toroidal field direction, evident from both in-situ spectroscopic and post-mortem non-spectroscopic measurements. The gross Al erosion yield was estimated from film thickness change measurements of small area samples, and was found to be ∼40–70% of the expected erosion yield based on theoretical physical sputtering yields after including sputtering by a 1–3% carbon impurity. The multi-step redeposition and re-erosion process, and hence the measured net erosion yield and material migration patterns, were found to be influenced by the surface roughness and/or porosity. A time-dependent model of material migration accounting for deposit accumulation in hidden areas was developed to reproduce the measurements in these experiments and determine a redeposition probability distribution function for sputtered atoms.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Additively manufactured (AM) austenitic stainless steels are intriguing candidates for the storage of gaseous hydrogen isotopes because complex vessel geometries can be built more easily than by using conventional machining options. Parts built with AM stainless steel tend to have excellent mechanical properties (with tensile strength, ductility, fatigue crack growth, and fracture toughness comparable to or exceeding that of wrought austenitic stainless steel). However, the solidification microstructures produced by AM processing differ substantially from the microstructures of wrought material. Some features may affect permeability, including some amount of porosity and a greater amount of ferrite. Because the diffusivity of hydrogen in ferrite is greater than in austenite (six orders of magnitude at ambient temperature), care must be taken to retain the performance that is taken for granted due to the base alloy chemistry. Furthermore, AM parts tend to have greater dislocation densities and greater amounts of carbon, nitrogen, and oxygen. These features, along with the austenite/ferrite interfaces, may contribute to greater hydrogen trapping. We report the results of our studies of deuterium transport in various austenitic (304L, 316, and 316L) steels produced by AM. Manufacturing by Powder Bed Fusion (PBF) and two different blown powder methods are considered here (Laser Engineered Net Shaping® (LENS®) and a Direct Laser Powder Deposition (DLPD) method with a higher laser power)). The hydrogen permeability (an equilibrium property) changes negligibly (less than a factor of 2), regardless of chemistry and processing method, when tested between 150 and 500°C. This is despite increases in ferrite content up to FN=2.7. However, AM materials exhibit greater hydrogen isotope trapping, as measured by permeation transients, thermal desorption spectra, and inert gas fusion measurement. The trapping energies are likely modest (<10 kJ/mol), but may indicate a larger population of trap sites than in conventional 300-series stainless steels.

Abstract not provided.

In this work, we examine the response of an ultra-fine grained (UFG) tungsten material to high-flux deuterium plasma exposure. UFG tungsten has received considerable interest as a possible plasma-facing material in magnetic confinement fusion devices, in large part because of its improved resistance to neutron damage. However, optimization of the material in this manner may lead to trade-offs in other properties. We address two aspects of the problem in this work: (a) how high-flux plasmas modify the structure of the exposed surface, and (b) how hydrogen isotopes become trapped within the material. The specific UFG tungsten considered here contains 100 nm-width Ti dispersoids (1 wt%) that limit the growth of the W grains to a median size of 960 nm. Metal impurities (Fe, Cr) as well as O were identified within the dispersoids; these species were absent from the W matrix. To simulate relevant particle bombardment conditions, we exposed specimens of the W-Ti material to low energy (100 eV), high-flux (> 1022 m− 2 s− 1) deuterium plasmas in the PISCES-A facility at the University of California, San Diego. To explore different temperature-dependent trapping mechanisms, we considered a range of exposure temperatures between 200 °C and 500 °C. For comparison, we also exposed reference specimens of conventional powder metallurgy warm-rolled and ITER-grade tungsten at 300 °C. Post-mortem focused ion beam profiling and atomic force microscopy of the UFG tungsten revealed no evidence of near-surface bubbles containing high pressure D2 gas, a common surface degradation mechanism associated with plasma exposure. Thermal desorption spectrometry indicated moderately higher trapping of D in the material compared with the reference specimens, though still within the spread of values for different tungsten grades found in the literature database. For the criteria considered here, these results do not indicate any significant obstacles to the potential use of UFG tungsten as a plasma-facing material, although further experimental work is needed to assess material response to transient events and high plasma fluence.

To address the transport and trapping of hydrogen isotopes, several permeation experiments are being pursued at both Sandia National Laboratories (deuterium gas-driven permeation) and Idaho National Laboratories (tritium gas- and plasma-driven tritium permeation). These experiments are in part a collaboration between the US and Japan to study the performance of tungsten at divertor relevant temperatures (PHENIX). Here we report on the development of a high temperature (≤1150 °C) gas-driven permeation cell and initial measurements of deuterium permeation in several types of tungsten: high purity tungsten foil, ITER-grade tungsten (grains oriented through the membrane), and dispersoid-strengthened ultra-fine grain (UFG) tungsten being developed in the US. Experiments were performed at 500–1000 °C and 0.1–1.0 atm D2 pressure. Permeation through ITER-grade tungsten was similar to earlier W experiments by Frauenfelder (1968–69) and Zaharakov (1973). Data from the UFG alloy indicates marginally higher permeability (< 10×) at lower temperatures, but the permeability converges to that of the ITER tungsten at 1000 °C. The permeation cell uses only ceramic and graphite materials in the hot zone to reduce the possibility for oxidation of the sample membrane. Sealing pressure is applied externally, thereby allowing for elevation of the temperature for brittle membranes above the ductile-to-brittle transition temperature.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

An associated particle neutron generator is described that employs a negative ion source to produce high neutron flux from a small source size. Negative ions produced in an rf-driven plasma source are extracted through a small aperture to form a beam which bombards a positively biased, high voltage target electrode. Electrons co-extracted with the negative ions are removed by a permanent magnet electron filter. The use of negative ions enables high neutron output (100% atomic ion beam), high quality imaging (small neutron source size), and reliable operation (no high voltage breakdowns). The neutron generator can operate in either pulsed or continuous-wave (cw) mode and has been demonstrated to produce 106 D-D n/s (equivalent to ~108 D-T n/s) from a 1 mm-diameter neutron source size to facilitate high fidelity associated particle imaging.

Abstract not provided.

Abstract not provided.