Publications

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Binders such as Estane, Teflon, Kel F and HTPB are typically used in heterogeneous explosives to bond polycrystalline constituents together as an energetic composite. Combined theoretical and experimental studies are underway to unravel the mechanical response of these materials when subjected to isentropic compression loading. Key to this effort is the determination of appropriate constitutive and EOS property data at extremely high stress-strain states as required for detailed mesoscale modeling. The Sandia Z accelerator and associated diagnostics provides new insights into mechanical response of these nonreactive constituents via isentropic ramp-wave compression loading. Several thicknesses of samples, varied from 0.3 to 1.2 mm, were subjected to a ramp load of {approx}42 Kbar over 500 ns duration using the Sandia Z-machine. Profiles of transmitted ramp waves were measured at window interfaces using conventional VISAR. Shock physics analysis is then used to determine the nonlinear material response of the binder materials. In this presentation we discuss experimental and modeling details of the ramp wave loading ICE experiments designed specifically for binder materials.

Abstract not provided.

Abstract not provided.

The shock compaction behavior of a tungsten carbide powder was investigated using a new experimental design for gas-gun experiments. This design allows the Hugoniot properties to be measured with reasonably good accuracy despite the inherent difficulties involved with distended powders. The experiments also provide the first reshock state for the compacted powder. Experiments were conducted at impact velocities of 245, 500, and 711 m/s. A steady shock wave was observed for some of the sample thicknesses, but the remainder were attenuated due to release from the back of the impactor or the edge of the sample. The shock velocity for the powder was found to be quite low, and the propagating shock waves were seen to be very dispersive. The Hugoniot density for the 711 m/s experiment was close to ambient crystal density for tungsten carbide, indicating nearly complete compaction. When compared with quasi-static compaction results for the same material, the dynamic compaction data is seen to be significantly stiffer for the regime over which they overlap. Based on these initial results, recommendations are made for improving the experimental technique and for future work to improve our understanding of powder compaction.

Abstract not provided.

Abstract not provided.

Of special promise for providing dynamic mesoscale response data is the line-imaging VISAR, an instrument for providing spatially resolved velocity histories in dynamic experiments. We have prepared two line-imaging VISAR systems capable of spatial resolution in the 10-20 micron range, at the Z and STAR facilities. We have applied this instrument to selected experiments on a compressed gas gun, chosen to provide initial data for several problems of interest, including: (1) pore-collapse in copper (two variations: 70 micron diameter hole in single-crystal copper) and (2) response of a welded joint in dissimilar materials (Ta, Nb) to ramp loading relative to that of a compression joint. The instrument is capable of resolving details such as the volume and collapse history of a collapsing isolated pore.

The high-pressure response of cryogenic liquid deuterium (LD{sub 2}) has been studied to pressures of {approx}400GPa and densities of {approx}1.5g/cm{sup 3}. Using intense magnetic pressure produced by the Sandia National Laboratories Z accelerator, macroscopic aluminum or titanium flyer plates, several mm in lateral dimensions and a few hundred microns in thickness, have been launched to velocities in excess of 22 km/s, producing constant pressure drive times of approximately 30 ns in plate impact, shock wave experiments. This flyer plate technique was used to perform shock wave experiments on LD{sub 2} to examine its high-pressure equation of state. Using an impedance matching method, Hugoniot measurements of LD{sub 2} were obtained in the pressure range of {approx}22-100GPa. Results of these experiments indicate a peak compression ratio of approximately 4.3 on the Hugoniot. In contrast, previously reported Hugoniot states inferred from laser-driven experiments indicate a peak compression ratio of approximately 5.5-6 in this same pressure range. The stiff Hugoniot response observed in the present impedance matching experiments was confirmed in simultaneous, independent measurements of the relative transit times of shock waves reverberating within the sample cell, between the front aluminum drive plate and the rear sapphire window. The relative timing was found to be sensitive to the density compression along the principal Hugoniot. Finally, mechanical reshock measurements of LD{sub 2} using sapphire, aluminum, and {alpha}-quartz anvils were made. These results also indicate a stiff response, in agreement with the Hugoniot and reverberating wave measurements. Using simple model-independent arguments based on wave propagation, the principal Hugoniot, reverberating wave, and sapphire anvil reshock measurements are shown to be internally self-consistent, making a strong case for a Hugoniot response with a maximum compression ratio of {approx}4.3-4.5. The trends observed in the present data are in very good agreement with several ab initio models and a recent chemical picture model for LD{sub 2}, but in disagreement with previously reported laser-driven shock results. Due to this disagreement, significant emphasis is placed on the discussion of uncertainties, and the potential systematic errors associated with each measurement.

Abstract not provided.

Abstract not provided.

The pulsed-power Z machine, in an isentropic compression experiment (ICE) mode, will allow the dynamic characterization of porous materials - here various ceramic powders, e.g., Al{sub 2}O{sub 3}, WC, ZrO{sub 2} - at roughly half their solid densities. A cylindrical configuration can provide megabar-level loads on an annulus of the sample material. Data will be provided by velocity interferometers that measure free-surface (or possibly interface) particle velocities. Differing sample thicknesses using stepped or conical geometries yield experimental efficiency by allowing multiple data records on single shots. With the p/{alpha} model for porous materials, the one-dimensional Lagrangian hydrocode WONDY provides the needed analyses. Based on static data, both power-law and quadratic crush curves are employed. Within the model constraints, we suggest that the most important parameter for characterizing the material is the crush strength, p{sub s}. With adequate sample thicknesses, the planned velocity measurements differentiate among the various assumptions for p{sub s}.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Using intense magnetic pressure, a method was developed to launch flyer plates to velocities in excess of 20 km s{sup -1}. This technique was used to perform plate-impact, shock wave experiments on cryogenic liquid deuterium (LD{sub 2}) to examine its high-pressure equation of state (EOS). Using an impedance matching method, Hugoniot measurements were obtained in the pressure range of 22--100 GPa. The results of these experiments disagree with the previously reported Hugoniot measurements of LD2 in the pressure range above {approx}40 GPa, but are in good agreement with first principles, ab initio models for hydrogen and its isotopes.

Abstract not provided.

Abstract not provided.