Publications

Abstract not provided.

Abstract not provided.

Abstract not provided.

A measurement instrument utilizing dual, chromatic, confocal, distance sensors has been jointly developed by General Atomics and Sandia National Laboratories (SNL) for thickness and flatness measurement of target components used in dynamic materials properties (DMP) experiments on the SNL Z-Machine (Z). Compared to previous methods used in production of these types of targets, the tool saves time and yields a 4× reduction in thickness uncertainty which is one of the largest sources of error in equation of state measurements critical to supporting the National Nuclear Security Administration Stockpile Stewardship program and computer modeling of high energy density experiments. It has numerous differences from earlier instruments operating on the dual confocal sensor principle to accommodate DMP components including larger lateral travel, longer working distance, ability to measure flatness in addition to thickness, built-in thickness calibration standards for quickly checking calibration before and after each measurement, and streamlined operation. Thickness and flatness of 0.2- to 3.3-mm-thick sections of diamond-machined copper and aluminum can be measured to submicron accuracy. Sections up to 6 mm thick can be measured with as-yet undetermined accuracy. Samples must have one surface which is flat to within 300 µm, lateral dimensions of no more than 50 ×50 mm, and height less than 40 mm.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

The CHEDS researchers are engaged in a collaborative research project to study the properties of iron and iron alloys under Earth’s core conditions. The Earth’s core, inner and outer, is composed primarily of iron, thus studying iron and iron alloys at high pressure and temperature conditions will give the best estimate of its properties. Also, comparing studies of iron alloys with known properties of the core can constrain the potential light element compositions found within the core, such as fitting sound speeds and densities of iron alloys to established inner- Earth models. One of the lesser established properties of the core is the thermal conductivity, where current estimates vary by a factor of three. Therefore, one of the primary goals of this collaboration is to make relevant measurements to elucidate this conductivity.

Abstract not provided.

Dynamic materials properties experiments on Sandia National Laboratories Z Machine require increasingly precise electrical current pulse shaping. In the experiment described here, a copper flyer plate is accelerated from rest to 1,600 m/s over a 40 micron flight gap in 50 ns. This flyer then impacts a cerium sample, shock melting the cerium, before subsequent quasi-isentropic ramping to mega-bar pressures. Through predictive simulations, postdicted analysis, and a new computational tool for characterizing inherent Z Machine timing accuracy, qualitative estimates of pulse controllability and experimental design robustness are arrived upon.

Single crystal lithium fluoride (LiF), oriented [100], was shock loaded and subsequently shocklessly compressed in two experiments at the Z Machine. Velocimetry measurements were employed to obtain an impactor velocity, shock transit times, and in-situ particle velocities for LiF samples up to ∼1.8 mm thick. A dual thickness Lagrangian analysis was performed on the in-situ velocimetry data to obtain the mechanical response along the loading path of these experiments. An elastic response was observed on one experiment during initial shockless compression from 100 GPa before yielding. The relatively large thickness differences utilized for the dual sample analyses (up to ∼1.8 mm) combined with a relative timing accuracy of ∼0.2 ns resulted in an uncertainty of less than 1% on density and stress at ∼200 GPa peak loading on one experiment and <4% on peak loading at ∼330 GPa for another. The stress-density analyses from these experiments compare favorably with recent equation of state models for LiF.

The capability for statically pre-compressing fluid targets for Hugoniot measurements utilizing gas gun driven flyer plates has been developed. Pre-compression expands the capability for initial condition control, allowing access to thermodynamic states off the principal Hugoniot. Absolute Hugoniot measurements with an uncertainty less than 3% on density and pressure were obtained on statically pre-compressed fluid helium utilizing a two stage light gas gun. Helium is highly compressible; the locus of shock states resulting from dynamic loading of an initially compressed sample at room temperature is significantly denser than the cryogenic fluid Hugoniot even for relatively modest (0.27-0.38 GPa) initial pressures. The dynamic response of pre-compressed helium in the initial density range of 0.21-0.25 g/cm3 at ambient temperature may be described by a linear shock velocity (us) and particle velocity (up) relationship: us = C0 + sup, with C0 = 1.44 ± 0.14 km/s and s = 1.344 ± 0.025.

Abstract not provided.

Abstract not provided.

The Thor pulsed power generator is being developed at Sandia National Laboratories . The design consists of up to 288 decoupled an d transit time isolated ca pacitor - switch units , called "bricks" , that can be individually triggered to achieve a high degree of p ulse tailoring for magnetically - driven isentropic compression experiments (ICE). The connecting transmission lines are impedance matched to the bricks, a llowing the capacitor energy to be efficiently delivered to an ICE strip - line load with pe ak pressures of over 100 GPa . Thor will drive experiments to expl ore equation of state, material strength, and phase transition properties of a wide variety of materi als. We present an optimization process for producing tailored current pulses, a requirement for many material studies, on the Thor generator . This technique, which is unique to the novel "current - adder" architecture used by Thor, entirely avoids the itera tive use of complex circuit models to converge to the desired electrical pulse . We describe the optimization procedure for the Thor design and show results for various materials of interest. Also, we discuss the extension of these concepts to the megajoule - class Neptune machine design. Given this design, we are able to design shockless ramp - driven experiments in the 1 TPa range of material pressure.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

We have developed the design of Thor: a pulsed power accelerator that delivers a precisely shaped current pulse with a peak value as high as 7 MA to a strip-line load. The peak magnetic pressure achieved within a 1-cm-wide load is as high as 100 GPa. Thor is powered by as many as 288 decoupled and transit-time isolated bricks. Each brick consists of a single switch and two capacitors connected electrically in series. The bricks can be individually triggered to achieve a high degree of current pulse tailoring. Because the accelerator is impedance matched throughout, capacitor energy is delivered to the strip-line load with an efficiency as high as 50%. We used an iterative finite element method (FEM), circuit, and magnetohydrodynamic simulations to develop an optimized accelerator design. When powered by 96 bricks, Thor delivers as much as 4.1 MA to a load, and achieves peak magnetic pressures as high as 65 GPa. When powered by 288 bricks, Thor delivers as much as 6.9 MA to a load, and achieves magnetic pressures as high as 170 GPa. We have developed an algebraic calculational procedure that uses the single brick basis function to determine the brick-triggering sequence necessary to generate a highly tailored current pulse time history for shockless loading of samples. Thor will drive a wide variety of magnetically driven shockless ramp compression, shockless flyer plate, shock-ramp, equation of state, material strength, phase transition, and other advanced material physics experiments.

Abstract not provided.