Publications

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Exhaust gas recirculation (EGR) can be used to mitigate knock in SI engines. However, experiments have shown that the effectiveness of various EGR constituents to suppress knock varies with fuel type and compression ratio (CR). To understand some of the underlying mechanisms by which fuel composition, octane sensitivity (S), and CR affect the knock-mitigation effectiveness of EGR constituents, the current paper presents results from a chemical-kinetics modeling study. The numerical study was conducted with CHEMKIN, imposing experimentally acquired pressure traces on a closed reactor model. Simulated conditions include combinations of three RON-98 (Research Octane Number) fuels with two octane sensitivities and distinctive compositions, three EGR diluents, and two CRs (12:1 and 10:1). The experimental results point to the important role of thermal stratification in the end-gas to smooth peak heat-release rate (HRR) and prevent acoustic noise. To model the effects of thermal stratification due to heat-transfer losses to the combustion-chamber walls, the initial temperature at the start of the CHEMKIN simulation was successively reduced below the adiabatic core temperature while observing changes in end-gas heat release and its effect on the reactant temperature. The results reveal that knock-prone conditions generally exhibit an increased amount of heat release in the colder temperature zones, thus counteracting the HRR-smoothing effect of the naturally occurring thermal stratification. This detrimental effect becomes more pronounced for the low-S fuel due to its significant Negative Temperature Coefficient (NTC) autoignition characteristics. This explains the generally reduced effectiveness of dilution for the low-S fuel, and higher knock intensity for the cycles with autoignition.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

This study shows fuel film measurements in a spark-ignited direct injection engine using refractive index matching (RIM). The RIM technique is applied to measure the fuel impingement of a high research octane number gasoline fuel with 30 vol% ethanol content at two intake pressures and coolant temperatures. Measurements are conducted for an alkylate fuel at one operating case, as well. It is shown that the fuel volume on the piston surface increases for lower intake pressure and lower coolant temperature and that the alkylate fuel shows very little spray impingement. The fuel films can be linked to increased soot emissions. A detailed description of the calibration technique is provided and measurement uncertainties are discussed. The dependency of the RIM signal on refractive index changes is measured. The RIM technique provides quantitative film thickness measurements up to 0.9 µm in this engine. For thicker films, semi-quantitative results of film thickness can be utilized to study the distribution of impinged fuel.

Abstract not provided.

Abstract not provided.

Ever tighter fuel economy standards and concerns about energy security motivate efforts to improve engine efficiency and to develop alternative fuels. This project contributes to the science base needed by industry to develop highly efficient direct injection spark ignition (DISI) engines that also beneficially exploit the different properties of alternative fuels. Here, the emphasis is on lean operation, which can provide higher efficiencies than traditional non-dilute stoichiometric operation. Since lean operation can lead to issues with ignition stability, slow flame propagation and low combustion efficiency, the focus is on techniques that can overcome these challenges. Specifically, fuel stratification is used to ensure ignition and completeness of combustion but this technique has soot and NOx emissions challenges. For ultra-lean well-mixed operation, turbulent deflagration can be combined with controlled end-gas autoignition to render mixed-mode combustion for sufficiently fast heat release. However, such mixed-mode combustion requires very stable inflammation, motivating studies on the effects of near-spark flow and turbulence, and the use of small amounts of fuel stratification near the spark plug.

Improved engine efficiency is required to comply with future fuel economy standards. Alternative fuels have the potential to enable more efficient engines while addressing concerns about energy security. This project contributes to the science base needed by industry to develop highly efficient direct injection spark igniton (DISI) engines that also beneficially exploit the different properties of alternative fuels. Here, the emphasis is on quantifying autoignition behavior for a range of spark-ignited engine conditions, including directly injected boosted conditions. The efficiency of stoichiometrically operated spark ignition engines is often limited by fuel-oxidizer end-gas autoignition, which can result in engine knock. A fuel’s knock resistance is assessed empirically by the Research Octane Number (RON) and Motor Octane Number (MON) tests. By clarifying how these two tests relate to the autoignition behavior of conventional and alternative fuel formulations, fuel design guidelines for enhanced engine efficiency can be developed.

Lean or dilute spark-ignition engine operation can provide efficiency improvements relative to that of traditional well-mixed stoichiometric spark-ignition operation. However, to maintain a sufficiently short burn duration with the direct-injection spark-ignition engine hardware of the current study, mixed-mode combustion is required for operation with ϕ < 0.6. Such mixed-mode combustion uses a combination of deflagration and end-gas autoignition whereby the pressure rise of the deflagration-based combustion compresses the end-gas reactants to the point of autoignition. For better understanding of the transition from deflagration to autoignition, it is desirable to apply optical diagnostics. However, with the use of a single centrally located spark plug, the end-gas is found at the periphery of the combustion chamber, where it is difficult to examine optically. To overcome this, two additional spark plugs were mounted in the pent-roof gables (called East and West). Performance testing was performed for five different spark strategies: Central Only, East-West, ALL Three, East Only, and West Only. The five spark strategies are combined with swirl or no-swirl operation for a total of 10 ϕ-sweeps. A high-octane E30 fuel is used here, and intake heating is used to promote both lean combustion stability and end-gas autoignition. The best lean combustion stability is found for the ALL Three spark strategy, followed by the East-West and Central spark strategies, enabling stable mixed-mode spark-ignition combustion for ϕ down to 0.50 and 0.55, respectively. Here, operation without swirl provides the most stable combustion. High-speed imaging of ultra-lean operation without swirl at ϕ = 0.55 using the East-West spark strategy reveals that the transition from deflagration to end-gas autoignition frequently occurs within the view offered by the small piston-bowl window. These results encourage future optical investigations of fuel effects on this transition process, but a larger piston-bowl window is recommended.

The use of exhaust gas recirculation (EGR) in spark ignition engines has been shown to have a number of beneficial effects under specific operating conditions. These include reducing pumping work under part load conditions, reducing NOx emissions and heat losses by lowering peak combustion temperatures, and by reducing the tendency for engine knock (caused by end-gas autoignition) under certain operating regimes. In this study, the effects of EGR addition on knocking combustion are investigated through a combined experimental and modeling approach. The problem is investigated by considering the effects of individual EGR constituents, such as CO2, N2, and H2O, on knock, both individually and combined, and with and without traces species, such as unburned hydrocarbons and NOx. The effects of engine compression ratio and fuel composition on the effectiveness of knock suppression with EGR addition were also investigated. A parametric, experimental matrix of diluents, compression ratio, and fuels was tested to measure knock-limited combustion phasing of each combination. The resulting knock limits were evaluated in the context of thermodynamic effects on the closed cycle, chemical interactions between the EGR constituents and the fuel-oxidizer mixture, and the effect of altered pressure-temperature trajectories on fuel-autoignition behavior. This paper provides an overview of the experimental results, and uses chemical-kinetic modeling to investigate the behavior of a particular fuel - diluent combination which had a strong sensitivity to compression ratio variation. The numerical results shed light on the complex interactions between fuel chemistry, the engine's thermodynamic cycle, and the effect of residence times on the autoignition chemistry which leads to knock. An important and fuel-dependent role of thermal stratification in the end-gas is also suggested by the chemical-kinetics modeling of the experimentally observed knock limits.

This study evaluates the applicability of the Octane Index (OI) framework under conventional spark ignition (SI) and “beyond Research Octane Number (RON)” conditions using nine fuels operated under stoichiometric, knock-limited conditions in a direct injection spark ignition (DISI) engine, supported by Monte Carlo-type simulations which interrogate the effects of measurement uncertainty. Of the nine tested fuels, three fuels are “Tier III” fuel blends, meaning that they are blends of molecules which have passed two levels of screening, and have been evaluated to be ready for tests in research engines. These molecules have been blended into a four-component gasoline surrogate at varying volume fractions in order to achieve a RON rating of 98. The molecules under consideration are isobutanol, 2-butanol, and diisobutylene (which is a mixture of two isomers of octene). The remaining six fuels were research-grade gasolines of varying formulations. The DISI research engine was used to measure knock limits at heated and unheated intake temperature conditions, as well as throttled and boosted intake pressures, all at an engine speed of 1400 rpm. The tested knock-limited operating conditions conceptually exist both between the Motor Octane Number (MON) and RON conditions, as well as “beyond RON” conditions (conditions which are conceptually at lower temperatures, higher pressures, or longer residence times than the RON condition). In addition to directly assessing the performance of the Tier III blends relative to other gasolines, the OI framework was evaluated with considerations of experimental uncertainty in the knock-limited combustion phasing (KL-CA50) measurements, as well as RON and MON test uncertainties. The OI was found to hold to the first order, explaining more than 80% of the knock-limited behavior, although the remaining variation in fuel performance from OI behavior was found to be beyond the likely experimental uncertainties. This indicates that the effects of specific fuel components on knock which are not captured by RON and MON ratings, and complicating the assessment of a given fuel by RON and MON ratings alone.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.