Publications

Abstract not provided.

High-energy photons and neutrons can be used to actively interrogate for heavily shielded special nuclear material (SNM), such as HEU (highly enriched uranium), by detecting prompt and/or delayed induced fission signatures. In this work, we explore the underlying physics for a new type of photon source that generates high fluxes of mono-energetic gamma-rays from low-energy (<500 keV) proton-induced nuclear reactions. The characteristic energies (4- to 18-MeV) of the gamma-rays coincide with the peak of the photonuclear cross section. The source could be designed to produce gamma-rays of certain selected energies, thereby improving the probability of detecting shielded HEU or providing a capability to determine enrichment inside sealed containers. The fundamental physics of such an interrogation source were studied in this LDRD through scaled ion accelerator experiments and radiation transport modeling. The data were used to assess gamma and neutron yields, background, and photofission-induced signal levels from several (p,{gamma}) target materials under consideration.

A new nuclear microscopy technique called ion photon emission microscopy or IPEM was recently invented. IPEM allows analysis involving single ions, such as ion beam induced charge (IBIC) or single event upset (SEU) imaging using a slightly modified optical microscope. The spatial resolution of IPEM is currently limited to more than 10 μm by the scattering and reflection of ion-induced photons, i.e. light blooming or spreading, in the ionoluminescent phosphor layer. We are developing a "Microscopic Gridded Phosphor" (also called Black Matrix) where the phosphor nanocrystals are confined within the gaps of a micrometer scale opaque grid, which limits the amount of detrimental light blooming. MeV-energy proton beam lithography is ideally suited to lithographically form masks for the grid because of high aspect ratio, pattern density and sub-micron resolution of this technique. In brief, the fabrication of the grids was made in the following manner: (1) a MeV proton beam focused to 1.5-2 μm directly fabricated a matrix of pillars in a 15 μm thick SU-8 lithographic resist; (2) 7:1 aspect ratio pillars were then formed by developing the proton exposed area; (3) Ni (Au) was electrochemically deposited onto Cu-coated Si from a sulfamate bath (or buffered CN bath); (4) the SU-8 pillars were removed by chemical etching; finally (5) the metal micro-grid was freed from its substrate by etching the underlying Cu layer. Our proposed metal micro-grids promise an order-of-magnitude improvement in the resolution of IPEM. © 2005 Elsevier B.V. All rights reserved.

Abstract not provided.

The ion photon emission microscope, or IPEM, is the first device that allows scientists to microscopically study the effects of single ions in air on semiconductors, microchips and even biological cells without having to focus the beam. Reported here is a prototype, the size of a conventional optical microscope, developed at Sandia. The alpha-IPEM, that employs alpha particles from a radioactive source, represents the first example of IBA imaging without an accelerator. The IPEM resolution is currently limited to 10 {micro}m, but we also report a gridded-phosphor approach that could improve this resolution to that of the optical microscope, or {approx} 1 {micro}m. Finally, we propose that a simple adaptation of the alpha-IPEM could be the only way to maintain the high utility of radiation effects microscopy into the future.

Abstract not provided.

The irradiation of thin insulating films by high-energy ions (374 MeV Au{sup +25} or 241 MeV I{sup +19}) was used to attempt to form nanometer-size pores through the films spontaneously. Such ions deposit a large amount of energy into the target materials ({approx}20 keV/nm), which significantly disrupts their atomic lattice and sputters material from the surfaces, and might produce nanopores for appropriate ion-material combinations. Transmission electron microscopy was used to examine the resulting ion tracks. Tracks were found in the crystalline oxides quartz, sapphire, and mica. Sapphire and mica showed ion tracks that are likely amorphous and exhibit pits 5 nm in diameter on the surface at the ion entrance and exit points. This suggests that nanopores might form in mica if the film thickness is less than {approx}10 nm. Tracks in quartz showed strain in the matrix around them. Tracks were not found in the amorphous thin films examined: 20 nm-SiN{sub x}, deposited SiOx, fused quartz (amorphous SiO{sub 2}), formvar and 3 nm-C. Other promising materials for nanopore formation were identified, including thin Au and SnO{sub 2} layers.

We have studied the feasibility of an innovative device to sample 1ns low-power single current transients with a time resolution better than 10 ps. The new concept explored here is to close photoconductive semiconductor switches (PCSS) with a Laser for a period of 10 ps. The PCSSs are in a series along a Transmission Line (TL). The transient propagates along the TL allowing one to carry out a spatially resolved sampling of charge at a fixed time instead of the usual timesampling of the current. The fabrication of such a digitizer was proven to be feasible but very difficult.

Microelectronic devices in satellites and spacecraft are exposed to high energy cosmic radiation. Furthermore, Earth-based electronics can be affected by terrestrial radiation. The radiation causes a variety of Single Event Effects (SEE) that can lead to failure of the devices. High energy heavy ion beams are being used to simulate both the cosmic and terrestrial radiation to study radiation effects and to ensure the reliability of electronic devices. Broad beam experiments can provide a measure of the radiation hardness of a device (SEE cross section) but they are unable to pinpoint the failing components in the circuit. A nuclear microbeam is an ideal tool to map SEE on a microscopic scale and find the circuit elements (transistors, capacitors, etc.) that are responsible for the failure of the device. In this paper a review of the latest radiation effects microscopy (REM) work at Sandia will be given. Different SEE mechanisms (Single Event Upset, Single Event Transient, etc.) and the methods to study them (Ion Beam Induced Charge (IBIC), Single Event Upset mapping, etc.) will be discussed. Several examples of using REM to study the basic effects of radiation in electronic devices and failure analysis of integrated circuits will be given.

High-energy ion tracks (374 MeV Au{sup 26+}) in thin films were examined with transmission electron microscopy to investigate nanopore formation. Tracks in quartz and mica showed diffraction contrast. Tracks in sapphire and mica showed craters formed at the positions of ion incidence and exit, with a lower-density track connecting them. Direct nanopore formation by ions (without chemical etching) would appear to require film thicknesses less than 10 nm.

Sandia and Rontec have developed an annular, 12-element, 60 mm{sup 2}, Peltier-cooled, translatable, silicon drift detector called the SDD-12. The body of the SDD-12 is only 22.8 mm in total thickness and easily fits between the sample and the upstream wall of the Sandia microbeam chamber. At a working distance of 1 mm, the solid angle is 1.09 sr. The energy resolution is 170 eV at count rates <40 kcps and 200 eV for rates of 1 Mcps. X-ray count rates must be maintained below 50 kcps when protons are allowed to strike the full area of the SDD. Another innovation with this new {mu}PIXE system is that the data are analyzed using Sandia's Automated eXpert Spectral Image Analysis (AXSIA).

Abstract not provided.

Rare earth doped yttrium oxide (yttria) and silicate, Y{sub 2}O{sub 3}:Eu and Y{sub 2}SiO{sub 5}:Tb, are the most promising phosphors for advanced devices such as flat panel field-emission-displays. However, their light yield for electron excitation has proven to be lower than that predicted by early models. New experimental data are needed to improve the theoretical understanding of the cathodoluminescence (CL) that will, in turn, lead to materials that are significantly brighter. Beside the existing CL and photo luminescence (PL) measurements, one can provide new information by studying ion-induced luminescence (IL). Ions penetrate substantially deeper than electrons and their light yield should therefore not depend on surface effects. Moreover, the energy density released by ions can be much higher than that of electrons and photons, which results in possible saturation effects, further testing the adequacy of models. We exposed the above yttrium compounds to three ion beams, H (3 MeV), C (20 MeV), Cu (50 MeV), which have substantially different electronic stopping powers. H was selected to provide an excitation close to CL, but without surface effects. The C and Cu allowed an evaluation of saturation effects because of their higher stopping powers. The IL experiments involved measuring the transient light intensity signal radiating from thin phosphor layers following their exposure to {approx}200 ns ion beam pulses. We present the transient yield curves for the two materials and discuss a general model for this behavior.

Cross-sections for the elastic recoil of hydrogen isotopes, including tritium, have been measured for 4He2+ ions in the energy range of 9.0-11.6 MeV. These cross-sections have been measured at a scattering angle of 30° in the laboratory frame. Cross-sections were measured by allowing a 4He2+ beam to fall incident on solid targets of ErH2, ErD2 and ErT2, each of 500 nm nominal thickness and known areal densities of H, D, T and Er. The uncertainty in each cross-section is estimated to be ±3.2%. Published by Elsevier B.V.

Hydrogen isotope thin film standards have been manufactured at Sandia National Laboratories for use by the materials characterization community. Several considerations were taken into account during the manufacture of the ErHD standards, with accuracy and stability being the most important. The standards were fabricated by e-beam deposition of Er onto a Mo substrate and the film stoichiometrically loaded with hydrogen and deuterium. To determine the loading accuracy of the standards two random samples were measured by thermal desorption mass spectrometry and atomic absorption spectrometry techniques with a stated combined accuracy of ∼1.6% (1σ). All the standards were then measured by high energy RBS/ERD and RBS/NRA with the accuracy of the techniques ∼5% (1σ). The standards were then distributed to the IBA materials characterization community for analysis. This paper will discuss the suitability of the standards for use by the IBA community and compare measurement results to highlight the accuracy of the techniques used. © 2004 Elsevier B.V. All rights reserved.

Multiple scattering effects in ERD measurements are studied by comparing two Monte Carlo simulation codes, representing different approaches to obtain acceptable statistics, to experimental spectra measured from a HfO2 sample with a time-of-flight-ERD setup. The results show that both codes can reproduce the absolute detection yields and the energy distributions in an adequate way. The effect of the choice of the interatomic potential in multiple scattering effects is also studied. Finally the capabilities of the MC simulations in the design of new measurement setups are demonstrated by simulating the recoil energy spectra from a WCxNy sample with a low energy heavy ion beam. Published by Elsevier B.V.

We give the results of a study using Monte Carlo ion interaction codes to simulate and optimize elastic recoil detection analysis for {sup 3}He buildup in tritide films. Two different codes were used. The primary tool was MCERD, written especially for simulating ion beam analysis using optimizations and enhancements for greatly increasing the probabilities for the creation and the detection of recoil atoms. MPTRIM, an implementation of the TRIMRC code for a massively parallel computer, was also used for comparison and for determination of absolute yield. This study was undertaken because of a need for high-resolution depth profiling of 3He and near-surface light impurities (e.g. oxygen) in metal hydride films containing tritium.

The effects of photocurrents in nuclear weapons induced by proximal nuclear detonations are well known and remain a serious hostile environment threat for the US stockpile. This report describes the final results of an LDRD study of the physical phenomena underlying prompt photocurrents in microelectronic devices and circuits. The goals of this project were to obtain an improved understanding of these phenomena, and to incorporate improved models of photocurrent effects into simulation codes to assist designers in meeting hostile radiation requirements with minimum build and test cycles. We have also developed a new capability on the ion microbeam accelerator in Sandia's Ion Beam Materials Research Laboratory (the Transient Radiation Microscope, or TRM) to supply ionizing radiation in selected micro-regions of a device. The dose rates achieved in this new facility approach those possible with conventional large-scale dose-rate sources at Sandia such as HERMES III and Saturn. It is now possible to test the physics and models in device physics simulators such as Davinci in ways not previously possible. We found that the physical models in Davinci are well suited to calculating prompt photocurrents in microelectronic devices, and that the TRM can reproduce results from conventional large-scale dose-rate sources in devices where the charge-collection depth is less than the range of the ions used in the TRM.

To design more radiation-tolerant integrated circuits (ICs), it is necessary to design and test accurate models of ionizing-radiation-induced charge collection dynamics. A new technique, diffusion-time-resolved ion-beam-induced charge collection (DTRIBICC), is used to measure the average arrival time of the diffused charge, which is related to the average time of the arrival carrier density at the junction. Specially designed stripe-like test junctions are studied using a 12 MeV carbon microbeam with a spot size of ∼1 μm. The relative arrival time of ion-generated charge and the collected charge are measured using a multiple parameter data acquisition system. A 2-D device simulation code, MEDICI, is used to calculate the charge collection dynamics on the stripe-like test junctions. The simulations compare well with experimental microbeam measurements. The results show the importance of the diffused charge collection by junctions, which is especially significant for single-event upsets (SEUs) and m ultiple-event upsets (MEUs) in electronic devices. The charge sharing results also indicate that stripe-like junctions may be used as position-sensitive detectors with a resolution of ∼0.1 μm. © 2001 Elsevier Science B.V. All rights reserved.

Ion beam induced luminescence (IBIL) combined with ion beam induced charge collection (IBICC) is applied in a quantitative study of the IBIL generation yield and detection efficiency for several plastic phosphor materials. The main purpose of this study is to search for strongly luminescence materials that can be used to easily coat samples to be studied with ion-photon emission microscopy (IPEM). A special focus is given to plastic scintillation materials because thin films are easily prepared, and such films have already been used for single event triggering. The emission yield was found to be low for typical Bicron plastic phosphors (only ∼70 photons/ion/μm). The total collection, transmission and photon detection efficiency of the optical microscope used in this study was determined to be only ∼0.00003. For thin film plastic phosphors ∼20 μm thick, the detection efficiency was only 0.04 photons/ion. This means that using these plastics, IPEM would need to be performed with ∼20× more beam fluence to obtain data, such as IBICC, similar to a standard scanned nuclear microprobe. Improvements are discussed. © 2001 Elsevier Science B.V. All rights reserved.

Ion Beam Induced Luminescence (IBIL) and Ion Beam Induced Charge Collection (IBICC) have been applied in the study of the luminescence emission efficiency and investigation of the homogeneity of the luminescence emission in phosphors. The IBIL imaging was performed by using sharply focused ion beams or broad/partially-focused ion beams. The luminescence emission homogeneity in samples was examined to reveal possible distributed crystal-defects that may lead to the inhomogeneity of the luminescence emission in samples.The purpose of the study is to search for suitable luminescent thin films that have high homogeneity of luminescence emission, large IBIL efficiency under heavy ion excitation, and can be placed as a thin layer on the top of microelectronic devices to be analyzed with Ion Photon Emission Microscopy (IPEM). The emission yield was found to be low for organic materials, due to saturation of the light output dependence on the energy deposition of heavy ions. The emission yield of a typical Bicron plastic scintillator is about 70 photons/ion/micron. Inorganic materials may have higher IBIL yield under high-energy and heavy-ion excitation, but the challenging problem is the inhomogeneity of the IBIL emission. The IBIL image techniques are applied in the investigation of the homogeneity of a GaN epitaxial thin film, a zircon single crystal and a thin layer coated by Thiogallate(EuII) ceramic.

Ion Beam Induced Charge Collection (IBICC) is a proven albeit relatively new method to measure the electronic transport properties of room temperature radiation detectors. Using an ion microbeam, the charge collection efficiency of CZT detectors can be mapped with submicron resolution and maps of the electron mobility and lifetime can be calculated. The nuclear microprobe can be used not only for characterizing detectors but also with the use of Time Resolved IBICC (TRIBICC) and lateral IBICC/TRIBICC we can deduce information about the electron and hole mobility and lifetime profiles, and about the variation of electric field along the detectors' axes. The Sandia Nuclear Microprobe has been and is being used routinely to characterize CZT detectors and measure their electronic transport properties. In this paper we will present the results of these measurements for different detectors. Furthermore the damage effects caused by the probing beam will be discussed and a simple model will be presented to explain the characteristic charge collection efficiency pattern observed after high dose irradiation. © 2000 SPIE.

Abstract not provided.

Abstract not provided.

To design more radiation tolerant Integrated Circuits (ICs), it is essential to create and test accurate models of ionizing radiation induced charge collection dynamics within microcircuits. A new technique, Diffusion Time Resolved Ion Beam Induced Charge Collection (DTRIBICC), is proposed to measure the average arrival time of the diffused charge at the junction. Specially designed stripe-like junctions were experimentally studied using a 12 MeV carbon microbeam with a spot size of 1 {micro}m. The relative arrival time of ion-generated charge is measured along with the charge collection using a multiple parameter data acquisition system. The results show the importance of the diffused charge collection by junctions, which is especially significant in accounting for Multiple Bit Upset (MBUs) in digital devices.