Tritium diffusion in α-Zr containing point defects such as vacancies or self-interstitial atoms (SIAs) is simulated using molecular dynamics. Point defects rapidly aggregate to form extended defects, such as 3D nanoclusters and Frank loops. The geometry of extended defects is affected by the presence of tritium. At low temperature and in the absence of tritium, vacancies aggregate to form stacking fault pyramids. Addition of tritium at these temperatures promotes aggregation of vacancies to form 3D nanoclusters, within which the tritium concentration can be sufficiently high to suggest that these defects may serve as nucleation sites for hydride precipitation. Trapping of tritium in vacancy nanocluster reduces the calculated bulk diffusivity by an amount proportional to the vacancy concentration. At high temperature, vacancy clusters change shape to form planar basal dislocation loops, which bind tritium less strongly, leading to a sharp reduction in the fraction of trapped tritium and a corresponding increase in tritium diffusivity at high temperature. In contrast, SIAs increase tritium diffusion through α-Zr. Analysis of atomic trajectories shows that tritium does not interact directly with SIAs. Diffusion enhancement is instead related to expansion of the lattice.
A preliminary investigation of the use of supercritical carbon dioxide for treating of 3M 1860 N95 masks was undertaken to evaluate a potential route to low-cost, scalable, sterilization of personal protective equipment for multiple reuse in hospital settings. Upon entering the supercritical regime, the normally distinct liquid and gaseous phases of CO2 merge into a single homogeneous phase that has density, short-range order, and solvation capacity of a liquid, but the volume-filling and permeation properties that of a gas. This enables supercritical CO2 to function as a vehicle for delivery of biocidal agents such peracetic acid into microporous structures. The potentially adverse effect of a liquid-to-gas phase transition on mask filter media is avoided by conducting cleaning operations above 31 C, the critical temperature for carbon dioxide. A sample of fifteen 3M 1860 N95 masks was subjected to ten consecutive cycles of supercritical CO2 cleaning to determine its effect on mask performance. These 15 masks, along with 5 control samples then underwent a battery of standardized tests at the CDC NIOSH NPPTL research facility in Pittsburgh, PA. The data from these tests strongly suggest (but do not prove) that supercritical carbon dioxide do not damage 3M 1860 N95 masks. Additional tests conducted during this project confirmed the compatibility of supercritical CO2 with ventilator tubing that, like N95 masks, has been in short supply during portions of the COVID-19 pandemic and cannot be sterilized by conventional means. Finally, a control experiment was also conducted to examine the effect of supercritical CO2 on a BSL-2 surrogate virus, vesicular stomatitis virus (VSV), Indiana serotype strain. In the absence of biocidal additives, supercritical CO2 exhibited no measurable lethality against VSV. This surrogate virus experiment suggests that a biocidal additive such as peracetic acid will be necessary to achieve required sterilization metrics.
POur experiments indicated that upon a post-processing anneal, an additively manufactured 316L stainless steel exhibits cubic grains rather than the conventional equiaxed grains. Here, we have used kinetic Monte Carlo simulations to explore the origin of these cubic grains. First, we implemented a new kinetic Monte Carlo model in parallel code SPPARKS to simulate grain growth and recrystallization under a residual energy distribution. Our model incorporates physical properties and real-time, as opposed to generic properties and relative time. We further validated that our SPPARKS simulations reproduced the expected kinetic behavior of single-grain evolution. We then used the validated approach to simulate the anneal of an additively manufactured material under the same conditions used in our experiments. We found that the cubic grains can origin from a periodically varying residual energy that may be present in additively manufactured materials.
Austenitic stainless steels (Fe-Cr-Ni) are resistant to hydrogen embrittlement but have not been studied using molecular dynamics simulations due to the lack of an Fe-Cr-Ni-H interatomic potential. Herein we describe our recent progress towards molecular dynamics studies of hydrogen effects in Fe-Cr-Ni stainless steels. We first describe our Fe-Cr-Ni-H interatomic potential and demonstrate its characteristics relevant to mechanical properties. We then demonstrate that our potential can be used in molecular dynamics simulations to derive Arrhenius equation of hydrogen diffusion and to reveal twinning and phase transformation deformation mechanisms in stainless steels.