Publications

Abstract not provided.

Abstract not provided.

Nearly every manufacturing and many technologies central to Sandia's business involve physical processes controlled by interfacial wetting. Interfacial forces, e.g. conjoining/disjoining pressure, electrostatics, and capillary condensation, are ubiquitous and can surpass and even dominate bulk inertial or viscous effects on a continuum level. Moreover, the statics and dynamics of three-phase contact lines exhibit a wide range of complex behavior, such as contact angle hysteresis due to surface roughness, surface reaction, or compositional heterogeneities. These thermodynamically and kinetically driven interactions are essential to the development of new materials and processes. A detailed understanding was developed for the factors controlling wettability in multicomponent systems from computational modeling tools, and experimental diagnostics for systems, and processes dominated by interfacial effects. Wettability probed by dynamic advancing and receding contact angle measurements, ellipsometry, and direct determination of the capillary and disjoining forces. Molecular scale experiments determined the relationships between the fundamental interactions between molecular species and with the substrate. Atomistic simulations studied the equilibrium concentration profiles near the solid and vapor interfaces and tested the basic assumptions used in the continuum approaches. These simulations provide guidance in developing constitutive equations, which more accurately take into account the effects of surface induced phase separation and concentration gradients near the three-phase contact line. The development of these accurate models for dynamic multicomponent wetting allows improvement in science based engineering of manufacturing processes previously developed through costly trial and error by varying material formulation and geometry modification.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Encapsulation is a common process used in manufacturing most non-nuclear components including: firing sets, neutron generators, trajectory sensing signal generators (TSSGs), arming, fusing and firing devices (AF and Fs), radars, programmers, connectors, and batteries. Encapsulation is used to contain high voltage, to mitigate stress and vibration and to protect against moisture. The purpose of the ASCI Encapsulation project is to develop a simulation capability that will allow us to aid in the encapsulation design process, especially for neutron generators. The introduction of an encapsulant poses many problems because of the need to balance ease of processing and properties necessary to achieve the design benefits such as tailored encapsulant properties, optimized cure schedule and reduced failure rates. Encapsulants can fail through fracture or delamination as a result of cure shrinkage, thermally induced residual stresses, voids or incomplete component embedding and particle gradients. Manufacturing design requirements include (1) maintaining uniform composition of particles in order to maintain the desired thermal coefficient of expansion (CTE) and density, (2) mitigating void formation during mold fill, (3) mitigating cure and thermally induced stresses during cure and cool down, and (4) eliminating delamination and fracture due to cure shrinkage/thermal strains. The first two require modeling of the fluid phase, and it is proposed to use the finite element code GOMA to accomplish this. The latter two require modeling of the solid state; however, ideally the effects of particle distribution would be included in the calculations, and thus initial conditions would be set from GOMA predictions. These models, once they are verified and validated, will be transitioned into the SIERRA framework and the ARIA code. This will facilitate exchange of data with the solid mechanics calculations in SIERRA/ADAGIO.

We describe parallel simulations of viscous, incompressible, free surface, Newtonian fluid flow problems that include dynamic contact lines. The Galerlin finite element method was used to discretize the fully-coupled governing conservation equations and a ''pseudo-solid'' mesh mapping approach was used to determine the shape of the free surface. In this approach, the finite element mesh is allowed to deform to satisfy quasi-static solid mechanics equations subject to geometric or kinematic constraints on the boundaries. As a result, nodal displacements must be included in the set of problem unknowns. Issues concerning the proper constraints along the solid-fluid dynamic contact line in three dimensions are discussed. Parallel computations are carried out for an example taken from the coating flow industry, flow in the vicinity of a slot coater edge. This is a three-dimensional free-surface problem possessing a contact line that advances at the web speed in one region but transitions to static behavior in another part of the flow domain. Discussion focuses on parallel speedups for fixed problem size, a class of problems of immediate practical importance.