Using chemical kinetic modeling and statistical analysis, we investigate the possibility of correlating key chemical "markers"-typically small molecules-formed during very lean (φ ∼0.001) oxidation experiments with near-stoichiometric (φ ∼1) fuel ignition properties. One goal of this work is to evaluate the feasibility of designing a fuel-screening platform, based on small laboratory reactors that operate at low temperatures and use minimal fuel volume. Buras et al. [Combust. Flame 2020, 216, 472-484] have shown that convolutional neural net (CNN) fitting can be used to correlate first-stage ignition delay times (IDTs) with OH/HO2measurements during very lean oxidation in low-T flow reactors with better than factor-of-2 accuracy. In this work, we test the limits of applying this correlation-based approach to predict the low-temperature heat release (LTHR) and total IDT, including the sensitivity of total IDT to the equivalence ratio, φ. We demonstrate that first-stage IDT can be reliably correlated with very lean oxidation measurements using compressed sensing (CS), which is simpler to implement than CNN fitting. LTHR can also be predicted via CS analysis, although the correlation quality is somewhat lower than for first-stage IDT. In contrast, the accuracy of total IDT prediction at φ = 1 is significantly lower (within a factor of 4 or worse). These results can be rationalized by the fact that the first-stage IDT and LTHR are primarily determined by low-temperature chemistry, whereas total IDT depends on low-, intermediate-, and high-temperature chemistry. Oxidation reactions are most important at low temperatures, and therefore, measurements of universal molecular markers of oxidation do not capture the full chemical complexity required to accurately predict the total IDT even at a single equivalence ratio. As a result, we find that φ-sensitivity of ignition delay cannot be predicted at all using solely correlation with lean low-T chemical speciation measurements.
Rapid molecular-weight growth of hydrocarbons occurs in flames, in industrial synthesis, and potentially in cold astrochemical environments. A variety of high- and low-temperature chemical mechanisms have been proposed and confirmed, but more facile pathways may be needed to explain observations. We provide laboratory confirmation in a controlled pyrolysis environment of a recently proposed mechanism, radical–radical chain reactions of resonance-stabilized species. The recombination reaction of phenyl (c-C6H5) and benzyl (c-C6H5CH2) radicals produces both diphenylmethane and diphenylmethyl radicals, the concentration of the latter increasing with rising temperature. A second phenyl addition to the product radical forms both triphenylmethane and triphenylmethyl radicals, confirming the propagation of radical–radical chain reactions under the experimental conditions of high temperature (1100–1600 K) and low pressure (ca. 3 kPa). Similar chain reactions may contribute to particle growth in flames, the interstellar medium, and industrial reactors.
Fan, Xuefeng; Sun, Wenyu; Gao, Yi; Hansen, Nils H.; Chen, Bingjie; Pitsch, Heinz; Yang, Bin
To further understand the combustion characteristics and the reaction pathways of acyclic ethers, the oxidation of di-n-propyl ether (DPE) was investigated in a jet-stirred reactor (JSR) combined with a photoionization molecular-beam mass spectrometer. The experiments were carried out at near-atmospheric pressure (700 Torr) and over a temperature range of 425–850 K. Based on the experimental data and previous studies on ether oxidation, a new kinetic model was constructed and used to interpret the oxidation chemistry of DPE. In DPE oxidation, a high reactivity at low temperatures and two negative temperature coefficient (NTC) zones were observed. These behaviors are explained in this work by taking advantage of the obtained species information and the modeling analyses: the two NTC zones are caused by the competition of chain branching and termination reactions of the fuel itself and specific oxidation intermediates, respectively. Furthermore, the general requirements to have double-NTC behavior are discussed. A variety of crucial fuel-specific C6 species, such as ketohydroperoxides and diones, were detected in the species pool of DPE oxidation. Their formation pathways are illuminated based on rate-of-production (ROP) analyses. Propanal was identified as the most abundant small molecule intermediate, and its related reactions have an important impact on the oxidation process of DPE. Both acetic acid and propionic acid were detected in high concentrations. A new formation pathway of propionic acid is proposed and incorporated into the kinetic model to achieve a more accurate prediction for propionic acid mole fractions.
We present a new experimental methodology for detailed experimental investigations of depolymerization reactions over solid catalysts. This project aims to address a critical need in fundamental research on chemical upcycling of polymers – the lack of rapid, sensitive, isomerselective probing techniques for the detection of reaction intermediates and products. Our method combines a heterogeneous catalysis reactor for the study of multiphase (gas/polymer melt/solid) systems, coupled to a vacuum UV photoionization time-of-flight mass spectrometer. This apparatus draws on our expertise in probing complex gas-phase chemistry and enables highthroughput, detailed chemical speciation measurements of the gas phase above the catalyst, providing valuable information on the heterogeneous catalytic reactions. Using this approach, we investigated the depolymerization of high-density polyethylene (HDPE) over Ir-doped zeolite catalysts. We showed that the product distribution was dominated by low-molecular weight alkenes with terminal C=C double bonds and revealed the presence of many methyl-substituted alkenes and alkanes, suggesting extensive methyl radical chemistry. In addition, we investigated the fundamental reactivity of model oligomer molecules n-butane and isobutane over ZSM-5 zeolites. We demonstrated the first direct detection of methyl radical intermediates, confirming the key role of methyl in zeolite-catalyzed activation of alkanes. Our results show the potential of this experimental method to achieve deep insight into the complex depolymerization reactions and pave the way for detailed mechanistic studies, leading to increased fundamental understanding of key processes in chemical upcycling of polymers.
The oxidation of neo-pentane was studied by combining experiments, theoretical calculations, and mechanistic developments to elucidate the impact of the 3rd O2 addition reaction network on ignition delay time predictions. The experiments were based on photoionization mass spectrometry in jet-stirred and time-resolved flow reactors allowing for sensitive detection of the keto-hydroperoxide (KHP) and keto-dihydroperoxide (KDHP) intermediates. With neo-pentane exhibiting a unique symmetric molecular structure, which consequently results only in single KHP and KDHP isomers, theoretical calculations of ionization and fragment appearance energies and of absolute photoionization cross sections enabled the unambiguous identification and quantification of the KHP intermediate. Its temperature and time-resolved profiles together with calculated and experimentally observed KHP-to-KDHP signal ratios were compared to simulation results based on a newly developed mechanism that describes the 3rd O2 addition reaction network. A satisfactory agreement was observed between the experimental data points and the simulation results, adding confidence to the model’s overall performance.
Fritz, Sean M.; Mishra, Piyush; Wullenkord, Julia; Fugazzi, Paul G.; Kohse-Höinghaus, Katharina; Zwier, Timothy S.; Hansen, Nils H.
Developing new experimental techniques that allow for species identification and quantification in the high-temperature environment of reacting flows is a continuing challenge in combustion research. Here, we combine broadband chirped-pulse microwave (rotational) spectroscopy with an atmospheric-pressure jet-stirred reactor as a novel method to identify key reactive intermediates in low-temperature and ozone-assisted oxidation processes. In these experiments, the gas sample, after being withdrawn from reactive dimethyl ether/O2/Ar, dimethoxy methane/O2/Ar, and ethylene/O2/O3/Ar mixtures, expands via a supersonic expansion into the high vacuum of a microwave spectrometer, where the rotationally cold ensemble of polar molecules is excited with short MW radiation frequency ramps (chirps). The response of the molecular ensemble is detected in the time domain and after a Fourier transformation, the spectral composition of the transient emission is obtained in the frequency domain. The observed rotational frequencies are uniquely correlated to molecular structures and allow for an unambiguous identification of the sampled species. Detection and identification of intermediates such as formaldehyde, methyl formate, formic acid, formic acid anhydride, and the primary ethylene ozonide via literature-known rotational frequencies are evidence for the superb identification capabilities of broadband chirped-pulse microwave spectroscopy. Strong-field coherence breaking is employed to identify and assign transitions due to a specific component. The observation of van der Waals complexes provides an opportunity to detect combustion intermediates and products that are impossible to detect by rotational spectroscopy as isolated molecules.
Fundamental chemistry in heterogeneous catalysis is increasingly explored using operando techniques in order to address the pressure gap between ultrahigh vacuum studies and practical operating pressures. Because most operando experiments focus on the surface and surface-bound species, there is a knowledge gap of the near-surface gas phase and the fundamental information the properties of this region convey about catalytic mechanisms. We demonstrate in situ visualization and measurement of gas-phase species and temperature distributions in operando catalysis experiments using complementary near-surface optical and mass spectrometry techniques. The partial oxidation of methanol over a silver catalyst demonstrates the value of these diagnostic techniques at 600 Torr (800 mbar) pressure and temperatures from 150 to 410 °C. Planar laser-induced fluorescence provides two-dimensional images of the formaldehyde product distribution that show the development of the boundary layer above the catalyst under different flow conditions. Raman scattering imaging provides measurements of a wide range of major species, such as methanol, oxygen, nitrogen, formaldehyde, and water vapor. Near-surface molecular beam mass spectrometry enables simultaneous detection of all species using a gas sampling probe. Detection of gas-phase free radicals, such as CH3 and CH3O, and of minor products, such as acetaldehyde, dimethyl ether, and methyl formate, provides insights into catalytic mechanisms of the partial oxidation of methanol. The combination of these techniques provides a detailed picture of the coupling between the gas phase and surface in heterogeneous catalysis and enables parametric studies under different operating conditions, which will enhance our ability to constrain microkinetic models of heterogeneous catalysis.
Adamson, Brian A.; Skeen, Scott A.; Ahmed, Musahid; Hansen, Nils H.
The irreversible dimerization of polycyclic aromatic hydrocarbons (PAHs)-typically pyrene (C16H10) dimerization-is widely used in combustion chemistry models to describe the soot particle inception step. This paper concerns itself with the detection and identification of dimers of flame-synthesized PAH radicals and closed-shell molecules and an experimental assessment of the role of these PAH dimers for the nucleation of soot. To this end, flame-generated species were extracted from an inverse co-flow flame of ethylene at atmospheric pressure and immediately diluted with excess nitrogen before the mixture was analyzed using flame-sampling tandem mass spectrometry with collision-induced fragmentation. Signal at m/z = 404.157 (C32H20) and m/z = 452.157 (C36H20) were detected and identified as dimers of closed-shell C16H10 and C18H10 monomers, respectively. A complex between a C13H9 radical and a C24H12 closed-shell PAH was observed at m/z = 465.164 (C37H21). However, a rigorous analysis of the flame-sampled mass spectra as a function of the dilution ratio, defined as the ratio of the flow rates of the diluent nitrogen to the sampled gases, indicates that the observed dimers are not flame-born, but are produced in the sampling line. In agreement with theoretical considerations, this paper provides experimental evidence that pyrene dimers cannot be a key intermediate in particle inception at elevated flame temperatures.
Liao, Handong; Kang, Shiqing; Hansen, Nils H.; Zhang, Feng; Yang, Bin
The influence of ozone addition on the low-temperature oxidation of dimethyl ether (DME) was investigated experimentally in an atmospheric-pressure jet-stirred reactor, over the temperature range of 400–800 K. Detailed speciation information was obtained by employing synchrotron vacuum ultraviolet photoionization mass spectrometry. Experimental results revealed that the ozone addition had a positive influence on the production of the highly reactive intermediates. Moreover, the low-temperature reactivity of DME was significantly enhanced, which resulted in the broadening of the temperature window of fuel consumption and intermediates formation at lower temperatures. Therefore, novel experimental data of the low temperature regime (400–500 K) could be obtained. The data set of this special temperature regime yielded insights into the DME low-temperature kinetics, which were further supported with modeling analysis based on two existing DME models (Metcalfe et al., 2013; Wang et al., 2015) combined with an ozone sub-mechanism (Zhao et al., 2016). The analysis showed that temperature-sensitive reactions such as the second oxygen channel could be nearly “frozen” at this low temperature (T < 440 K). Furthermore, the production of some intermediates was found to be strongly governed by reaction pairs, such as CH3OCH2 + O2 = CH3OCH2O2 and CH3OCH2 + O2 = 2CH2O + OH for the CH2O formation. This finding could be useful for examining branching ratios in both models, and the analysis suggested the further modification of the branching ratios for the oxygen addition to CH3OCH2O2 pathways and the CH3OCH2O2 self-reactions were required. Finally, the influences of the O3 addition in the sensitive reactions of the fuel initial low-temperature oxidation were investigated in this work. It was interesting to note that O3 addition could change the dominating reactions in the initial low-temperature oxidation, by the addition of some O3-related pathways with relatively high sensitivity.
Ring-enlargement reactions can provide a fast route towards the formation of six-membered single-ring or polycyclic aromatic hydrocarbons (PAHs). To investigate the participation of the cyclopentadienyl (C5H5) radical in ring-enlargement reactions in high-temperature environments, a mass-spectrometric study was conducted. Experimental access to the C5H5 high-temperature chemistry was provided by two counterflow diffusion flames. Cyclopentene was chosen as a primary fuel given the large amount of resonantly stabilized cyclopentadienyl radicals produced by its decomposition and its high tendency to form PAHs. In a second experiment, methane was added to the fuel stream to promote methyl addition pathways and to assess the importance of ring-enlargement reactions for PAH growth. The experimental dataset includes mole fraction profiles of small intermediate hydrocarbons and of several larger species featuring up to four condensed aromatic rings. Results show that, while the addition of methane enhances the production of methylcyclopentadiene and benzene, the concentration of larger polycyclic hydrocarbons is reduced. The increase of benzene is probably attributable to the interaction between the methyl and the cyclopentadienyl radicals. However, the formation of larger aromatics seems to be dominated only by the cyclopentadienyl driven molecular-growth routes which are hampered by the addition of methane. In addition to the experimental work, two chemical mechanisms were tested and newly calculated reaction rates for cyclopentadiene reactions were included. In an attempt to assess the impact of cyclopentadienyl ring-enlargement chemistry on the mechanisms' predictivity, pathways to form benzene, toluene, and ethylbenzene were investigated. Results show that the updated mechanism provides an improved agreement between the computed and measured aromatics concentrations. Nevertheless, a detailed study of the single reaction steps leading to toluene, styrene, and ethylbenzene would be certainly beneficial.
The effect of H2O injection on the combustion process of iso-octane was investigated with the aim to better understand the suitability of water addition as a potential engine control parameter for homogeneous-charge compression ignition (HCCI) combustion. Several experiments were combined including premixed low-pressure flames, a jet-stirred reactor (JSR) and a plug-flow reactor (PFR), both at atmospheric pressure, and a single-cylinder research engine (SCRE) operated with either iso-octane or RON 98 gasoline. The thermal effect of H2O addition was determined in laminar premixed iso-octane/O2/Ar flames (equivalence ratio Φ=1.4, 40 mbar) with H2O mole fractions of 0 to 0.22, where water addition reduced the temperature measured by laser-induced fluorescence (LIF) by up to 110 K. Speciation data were obtained from these flames as well as in the JSR (Φ=0.65, 933 mbar) and PFR experiments (Φ=0.65, 970 mbar) with and without H2O addition in the low- to intermediate temperature regime from 700–1100 K. The chemical analysis in these flame and reactor experiments was performed using molecular-beam mass spectrometry (MBMS) employing either electron ionization (EI) in the PFR and premixed flame or single-photon ionization (PI) by tunable vacuum-ultraviolet radiation in the JSR. The effects on species mole fractions were small which is supported by predictions from chemical-kinetic simulations. Quantitative speciation data of the exhaust gas of the SCRE were obtained by using Fourier-transform infrared (FTIR) spectroscopy. A very similar species pool was detected in the laboratory-scale experiments and for the engine operation. It is thus assumed that these results could assist in guiding both the improvement of fundamental chemical-kinetic as well as HCCI engine control models.
León, Larisa; Ruwe, Lena; Moshammer, Kai; Seidel, Lars; Shrestha, Krishna P.; Wang, Xiaoxiao; Mauss, Fabian; Kohse-Höinghaus, Katharina; Hansen, Nils H.
A comprehensive, chemically detailed mechanism for the combustion of 2-methyl-2-butene and n-pentane is presented to provide insights into the different sooting tendencies of these two structurally different C5 hydrocarbons. A hierarchically assembled mechanism has been developed to specifically target speciation data from low-pressure premixed flames of 2-methyl-2-butene [Ruwe et al., Combust. Flame, 175, 34-46, 2017] and newly measured mole fraction data for a fuel-rich (ɸ=1.8) n-pentane flame, in which species profiles up to phenol were quantified. The partially isomer-resolved chemical composition of this flame was determined using flame-sampling molecular-beam mass spectrometry with single-photon ionization by tunable, synchrotron-generated vacuum-ultraviolet radiation. The presented model, which includes a newly determined, consistent set of the thermochemistry data for the C5 species, presents overall satisfactory capabilities to predict the mole fraction profiles of common combustion intermediates. The analysis of the model predictions revealed the fuel-structure dependencies (i.e. saturated vs. unsaturated and linear vs. branched) of the formation of small aromatic species that are considered as soot precursors. The propensity of the 2-methyl-2-butene flame to form larger concentrations of aromatic species was traced back to the readily available formation routes of several small precursor molecules and the efficient formation of “first aromatic rings” beyond benzene.
Keto-hydroperoxides (KHPs) are reactive, partially oxidized intermediates that play a central role in chain-branching reactions during the gas-phase low-temperature oxidation of hydrocarbons and oxygenated species. Although multiple isomeric forms of the KHP intermediate are possible in complex oxidation environments when multiple reactant radicals exist that contain nonequivalent O2 addition sites, isomer-resolved data of KHPs have not been reported. In this work, we provide partially isomer-resolved detection and quantification of the KHPs that form during the low-temperature oxidation of tetrahydrofuran (THF, cycl.-O-CH2CH2CH2CH2-). We describe how these short-lived KHPs were detected, identified, and quantified using integrated experimental and theoretical approaches. The experimental approaches were based on direct molecular-beam sampling from a jet-stirred reactor operated at near-atmospheric pressure and at temperatures between 500 and 700 K, followed by mass spectrometry with single-photon ionization via tunable synchrotron-generated vacuum-ultraviolet radiation, and the identification of fragmentation patterns. The interpretation of the experiments was guided by theoretical calculations of ionization thresholds, fragment appearance energies, and photoionization cross sections. On the basis of the experimentally observed and theoretically calculated ionization and fragment appearance energies, KHP isomers could be distinguished as originating from H-abstraction reactions from either the α-C adjacent to the O atom or the β-C atoms. Temperature-dependent concentration profiles of the partially resolved isomeric KHP intermediates were determined in the range of 500-700 K, and the results indicate that the observed KHP isomers are formed overwhelmingly (∼99%) from the α-C THF radical. Comparisons of the partially isomer-resolved quantification of the KHPs to up-to-date kinetic modeling results reveal new opportunities for the development of a next-generation THF oxidation mechanism.
The formation of small polycyclic aromatic hydrocarbons (PAHs) and their precursors can be strongly affected by reactions of C5 species. For improving existing combustion mechanisms for small PAH formation, it is therefore valuable to understand the fuel-specific chemistry of C5 fuels. To this end, we provide quantitative isomer-resolved species profiles measured in a laminar premixed (ϕ = 1.8) low-pressure (4 kPa) flame of 1-pentene with photoionization molecular-beam mass spectrometry (PI-MBMS) using tunable synchrotron vacuum-ultraviolet (VUV) radiation. These experimental results are accompanied with numerical simulations, starting from models from the literature by Wang et al. [JetSurF version 2.0 (2010)] and Healy et al. [Energy Fuels 24 (2010) 1521–1528] that were developed for different fuels, but which include 1-pentene as an intermediate, and by Narayanaswamy et al. [Combust. Flame 157 (2010) 1879–1898] focusing on the small PAH chemistry. Taking observed discrepancies between experimental results and simulations into consideration, a mechanism for C5 chemistry was newly developed including PAH formation pathways, and its performance analyzed in detail. Special emphasis was placed on the initial fuel consumption of 1-pentene as well as on formation pathways of small aromatics. The mechanisms show differences regarding fuel decomposition and hydrocarbon growth reactions. These contribute to noticeable differences between the simulations with different models on one hand, and deviations between model predictions and experimental results on the other. While the new model presents overall satisfactory capabilities to predict the mole fraction profiles of common combustion intermediates, the predictive capability of the literature models was not fully satisfying for some intermediate species, including C4H6, C7H8, and C10H8. The results indicate that the fuel-specific C5 reaction routes as well as the mechanism for small PAH formation need further investigation.
Wang, Zhandong; Herbinet, Olivier; Hansen, Nils H.; Battin-Leclerc, Frédérique
The aim of this paper is to review recent progress in detection and quantification of hydroperoxides, and to understand their reaction kinetics in combustion environments. Hydroperoxides, characterized by an –OOH group, are ubiquitous in the atmospheric oxidation of volatile organic compounds (∼300 K), and in the liquid and gas phase oxidation of fuel components at elevated temperatures (∼400–1000 K). They are responsible for two-stage fuel ignition in internal combustion engines and they play an important role in the formation and evolution of secondary organic aerosols in the atmosphere. The introduction outlines the importance of hydroperoxide chemistry in combustion reaction processes. In addition to this main topic, the role of hydroperoxides in atmospheric and liquid phase oxidation chemistry is also introduced, for a more general perspective. The second part of this paper briefly reviews the mechanistic insights of hydroperoxide chemistry in combustion systems, including experimental detection of these reactive species before 2010. Since that time significant progress has been made by advanced diagnostic techniques like tunable synchrotron vacuum ultraviolet photoionization mass spectrometry and infrared cavity ring-down spectroscopy. The third chapter of this work summarizes progress in gas phase oxidation experiments to measure hydrogen peroxide, alkyl hydroperoxides, olefinic hydroperoxides, ketohydroperoxides, and more complex hydroperoxides that include as many as five oxygen atoms. The fourth section details recent advances in understanding the combustion chemistry of hydroperoxides, involving the formation of carboxylic acids and diones, as well as the development of oxidation models that include a third O2 addition reaction mechanism. Finally, challenges are discussed, and perspectives are offered regarding the future of accurately measuring molecule-specific hydroperoxide concentrations and understanding their respective reaction kinetics.
Baroncelli, Martina; Felsmann, Daniel; Hansen, Nils H.; Pitsch, Heinz
Given the multi-physical nature of coal combustion, the development and validation of detailed chemical models reproducing coal volatiles combustion under oxy-fuel conditions is a crucial step towards the advancement of predictive full-scale simulations. During the devolatilization process, a large variety of gases is released and undergoes secondary pyrolysis and oxidation reactions. Therefore, the ability to capture their interactions is a prerequisite for each chemical model used in its detailed or reduced form to simulate these processes. In this work, a high-resolution time-of-flight molecular-beam mass spectrometer was employed to enable fast and simultaneous detection of stable and unstable species in counterflow flames of typical light volatiles. Following an approach of increasing complexity, carbon dioxide and methane were progressively added to an argon diluted acetylene base flame. For the three flames investigated here, results showed a significant increase in the concentration of C2 and C3 hydrocarbons and oxygenated compounds caused by methane addition to the acetylene flame. By hindering the production of the butadienyl radical, the addition of methane induces the reduction of benzene which triggers the decrease of aromatic species. Conversely, CO2 addition did not have significant effects on intermediates. To guide and interpret the measurements, numerical simulations with two existing chemical models were performed and the results were found to be consistent with the experimental data for small hydrocarbons. Some discrepancies were found between the two model predictions and between simulations and experiments for C4 and C5 species. Additionally, numerical simulations were found to overestimate the role of the methyl radical in aromatics formation.
External electric field and plasma assisted combustion show great potential for combustion enhancement, e.g., emission and ignition control. To understand soot suppression by external electric fields and flame ignition in spark ignition engines, flame ion chemistry needs to be investigated and developed. In this work, comprehensive and systematic investigations of neutral and ion chemistry are conducted in premixed rich methane flames. Cations are measured by quadrupole molecular beam mass spectrometry (MBMS), and neutrals are measured by synchrotron vacuum ultra violet photoionization time of flight MBMS (SVUV-PI-TOF-MBMS). The molecular formula and dominant isomers of various measured cations are identified based on literature survey and quantum chemistry calculations. Experimentally, we found that H3O+ is the dominant cation in slightly rich flame (ϕ=1.5), but C3H3+ is the most significant in very rich flames (ϕ=1.8 and 2.0). An updated ion chemistry model is proposed and used to explain the effects of changing equivalence ratio. To further verify key ion-neutral reaction pathways, measured neutral profiles are compared with cation profiles experimentally. Detailed cation and neutral measurements and numerical simulations by this work help to understand and develop ion chemistry models. Deficiencies in our current understanding of ion chemistry are also highlighted to motivate further research.
The reaction network of the simplest Criegee intermediate (CI) CH2OO has been studied experimentally during the ozonolysis of ethylene. The results provide valuable information about plasma- and ozone-assisted combustion processes and atmospheric aerosol formation. A network of CI reactions was identified, which can be described best by the sequential addition of CI with ethylene, water, formic acid, and other molecules containing hydroxy, aldehyde, and hydroperoxy functional groups. Species resulting from as many as four sequential CI addition reactions were observed, and these species are highly oxygenated oligomers that are known components of secondary organic aerosols in the atmosphere. Insights into these reaction pathways were obtained from a near-atmospheric pressure jet-stirred reactor coupled to a high-resolution molecular-beam mass spectrometer. The mass spectrometer employs single-photon ionization with synchrotron-generated, tunable vacuum-ultraviolet radiation to minimize fragmentation via near-threshold ionization and to observe mass-selected photoionization efficiency (PIE) curves. Species identification is supported by comparison of the mass-selected, experimentally observed photo-ionization thresholds with theoretical calculations for the ionization energies. A variety of multi-functional peroxide species are identified, including hydroxymethyl hydroperoxide (HOCH2OOH), hydroperoxymethyl formate (HOOCH2OCHO), methoxymethyl hydroperoxide (CH3OCH2OOH), ethoxymethyl hydroperoxide (C2H5OCH2OOH), 2-hydroxyethyl hydroperoxide (HOC2H4OOH), dihydroperoxy methane (HOOCH2OOH), and 1-hydroperoxypropan-2-one [CH3C(O)CH2OOH]. A semi-quantitative analysis of the signal intensities as a function of successive CI additions and temperature provides mechanistic insights and valuable information for future modeling work of the associated energy conversion processes and atmospheric chemistry. This work provides further evidence that the CI is a key intermediate in the formation of oligomeric species via the formation of hydroperoxides.
Ruwe, Lena; Moshammer, Kai; Hansen, Nils H.; Kohse-Höinghaus, Katharina
In this study, we experimentally investigate the high-temperature oxidation kinetics of n-pentane, 1-pentene and 2-methyl-2-butene (2M2B) in a combustion environment using flame-sampling molecular beam mass spectrometry. The selected C5 fuels are prototypes for linear and branched, saturated and unsaturated fuel components, featuring different C-C and C-H bond structures. It is shown that the formation tendency of species, such as polycyclic aromatic hydrocarbons (PAHs), yielded through mass growth reactions increases drastically in the sequence n-pentane < 1-pentene < 2M2B. This comparative study enables valuable insights into fuel-dependent reaction sequences of the gas-phase combustion mechanism that provide explanations for the observed difference in the PAH formation tendency. First, we investigate the fuel-structure-dependent formation of small hydrocarbon species that are yielded as intermediate species during the fuel decomposition, because these species are at the origin of the subsequent mass growth reaction pathways. Second, we review typical PAH formation reactions inspecting repetitive growth sequences in dependence of the molecular fuel structure. Third, we discuss how differences in the intermediate species pool influence the formation reactions of key aromatic ring species that are important for the PAH growth process underlying soot formation. As a main result it was found that for the fuels featuring a CC double bond, the chemistry of their allylic fuel radicals and their decomposition products strongly influences the combination reactions to the initially formed aromatic ring species and as a consequence, the PAH formation tendency.
In-cylinder reforming of injected fuel during a negative valve overlap (NVO) recompression period can be used to optimize main-cycle combustion phasing for low-load low-temperature gasoline combustion (LTGC). The objective of this work is to examine the effects of reformate composition on main-cycle engine performance. An alternate-fire sequence was used to generate a common exhaust temperature and composition boundary condition for a cycle-of-interest, with performance metrics measured for these custom cycles. NVO reformate was also separately collected using a dump-valve apparatus and characterized by both gas chromatography (GC) and photoionization mass spectroscopy (PIMS). To facilitate gas sample analysis, sampling experiments were conducted using a five-component gasoline surrogate (iso-octane, n-heptane, ethanol, 1-hexene, and toluene) that matched the molecular composition, 50% boiling point, and ignition characteristics of the research gasoline. For the gasoline, it was found that an advance of the NVO start-of-injection (SOI) led to a corresponding advance in main-period combustion phasing as the combination of longer residence times and lower amounts of liquid spray piston impingement led to a greater degree of fuel decomposition. The effect was more pronounced as the fraction of total fuel injected in the NVO period increased. Main-period combustion phasing was also found to advance as the main-period fueling decreased. Slower kinetics for leaner mixtures were offset by a combination of increased bulk-gas temperature from higher charge specific heat ratios and increased fuel reactivity due to higher charge reformate fractions.
This work identifies classes of cool flame intermediates from nheptane low-temperature oxidation (e.g., < 750 K) in a jet-stirred reactor (JSR) and a cooperative fuel research (CFR) engine. The sampled species from the JSR were analyzed using a synchrotron vacuum ultraviolet radiation photoionization time-of-flight molecular-beam mass spectrometer and an atmospheric pressure chemical ionization orbitrap mass spectrometer; the latter was also used to analyze the sampled species from the CFR engine. The products can be classified by species with molecular formulas of C7H14Ox (x=0-5), C7H12Ox (x=0-4), C7H10Ox (x=0-4), CnH2n (n=2-6), CnH2n-2 (n=4-6), CnH2n+2O (n=1-4, 6), CnH2nO (n=1-6), CnH2n-2O (n=2-6), CnH2n-4O (n=4-6), CnH2n+2O2 (n=0-4, 7), CnH2nO2 (n=1-6), CnH2n-2O2 (n=2-6), CnH2n-4O2 (n=4-7), and CnH2nO3 (n=3-6). The identified intermediate species include mainly alkene, dienes, aldehyde/keto compounds, olefinic aldehyde/keto compounds, diones, cyclic ethers, peroxides, acids, and alcohols/ethers. Reaction pathways forming intermediates with the same carbon number as n-heptane are proposed and discussed. These experimental results should be helpful in the development of kinetic models for n-heptane and longer-chain alkanes.
This work provides new temperature-dependent mole fractions of elusive intermediates relevant to the low-temperature oxidation of dimethyl ether (DME). It extends the previous study of Moshammer et al. [J. Phys. Chem. A 2015, 119, 7361-7374 ] in which a combination of a jet-stirred reactor and molecular beam mass spectrometry with single-photon ionization via tunable synchrotron-generated vacuum-ultraviolet radiation was used to identify (but not quantify) several highly oxygenated species. Here, temperature-dependent concentration profiles of 17 components were determined in the range of 450-1000 K and compared to up-to-date kinetic modeling results. Special emphasis is paid toward the validation and application of a theoretical method for predicting photoionization cross sections that are hard to obtain experimentally but essential to turn mass spectral data into mole fraction profiles. The presented approach enabled the quantification of the hydroperoxymethyl formate (HOOCH2OCH2O), which is a key intermediate in the low-temperature oxidation of DME. The quantification of this keto-hydroperoxide together with the temperature-dependent concentration profiles of other intermediates including H2O2, HCOOH, CH3OCHO, and CH3OOH reveals new opportunities for the development of a next-generation DME combustion chemistry mechanism.
Wang, Zhandong; Zhang, Lidong; Moshammer, Kai F.; Popolan-Vaida, Denisia M.; Shankar, Vijai S.; Lucassen, Arnas; Hemken, Christian; Taatjes, Craig A.; Leone, Stephen R.; Kohse-Höinghaus, Katharina; Hansen, Nils H.; Dagaut, Philippe; Sarathy, S.M.
Chain-branching reactions represent a general motif in chemistry, encountered in atmospheric chemistry, combustion, polymerization, and photochemistry; the nature and amount of radicals generated by chain-branching are decisive for the reaction progress, its energy signature, and the time towards its completion. In this study, experimental evidence for two new types of chain-branching reactions is presented, based upon detection of highly oxidized multifunctional molecules (HOM) formed during the gas-phase low-temperature oxidation of a branched alkane under conditions relevant to combustion. The oxidation of 2,5-dimethylhexane (DMH) in a jet-stirred reactor (JSR) was studied using synchrotron vacuum ultra-violet photoionization molecular beam mass spectrometry (SVUV-PI-MBMS). Specifically, species with four and five oxygen atoms were probed, having molecular formulas of C8H14O4 (e.g., diketo-hydroperoxide/keto-hydroperoxy cyclic ether) and C8H16O5 (e.g., keto-dihydroperoxide/dihydroperoxy cyclic ether), respectively. The formation of C8H16O5 species involves alternative isomerization of OOQOOH radicals via intramolecular H-atom migration, followed by third O2 addition, intramolecular isomerization, and OH release; C8H14O4 species are proposed to result from subsequent reactions of C8H16O5 species. The mechanistic pathways involving these species are related to those proposed as a source of low-volatility highly oxygenated species in Earth's troposphere. At the higher temperatures relevant to auto-ignition, they can result in a net increase of hydroxyl radical production, so these are additional radical chain-branching pathways for ignition. The results presented herein extend the conceptual basis of reaction mechanisms used to predict the reaction behavior of ignition, and have implications on atmospheric gas-phase chemistry and the oxidative stability of organic substances.
For next-generation engines that operate using low-temperature gasoline combustion (LTGC) modes, a major issue remains poor combustion stability at low-loads. Negative valve overlap (NVO) enables enhanced main combustion control through modified valve timings to retain combustion residuals along with a small fuel injection that partially reacts during the recompression. While the thermal effects of NVO fueling on main combustion are well understood, the chemical effects of NVO reactions are less certain, especially oxygen-deficient reactions where fuel pyrolysis dominates. To better understand NVO period chemistry details, comprehensive speciation of engine samples collected at the end of the NVO cycle was performed by photoionization mass spectroscopy (PIMS) using synchrotron generated vacuum-ultraviolet light. Two operating conditions were explored: 1) a fuel lean condition with a short NVO fuel injection and a relatively high amount of excess oxygen in the NVO cycle (7%), and 2) a fuel-rich condition with a longer NVO fuel injection and low amount of NVO-cycle excess oxygen (4%). Samples were collected by a custom dump-valve apparatus from a direct injection, single-cylinder, automotive research engine operating under low-load LTGC and fueled by either isooctane or an 88-octane research certification gasoline. Samples were stored in heated stainless steel cylinders and transported to the Lawrence Berkeley National Laboratory Advanced Light Source for analysis using a Sandia National Laboratories flame sampling apparatus. For all isooctane fueled conditions, NVO cycle sample speciation from the PIMS measurements agreed well with previously reported GC sample measurements if the sum total of all isomer constituents from the PIMS measurements were considered. PIMS data, however, provides richer speciation information that is useful for validation of computational modeling approaches. The PIMS data also revealed that certain species for the GC diagnostic were either misidentified during the calibration process or not identified at all. Examples of unidentified species include several classes of oxygenates (e.g., ketenes, aldehydes, and simple alcohols) and simple aromatics (e.g., benzene and toluene). For the gasoline fueled NVO cycles, performance characteristics were well matched to corresponding isooctane fueled NVO cycles. However, significant PIMS cross-talk from a wide range of gasoline components restricted the sampling analysis to a handful of species. Nonetheless, it was confirmed that for fuel-lean NVO operation there was a comparable increase in acetylene with NVO injection timing retard that is attributed to the prevalence of locally-rich, piston-surface pool fires caused by fuel spray impingement.
The oxidation of 1,3-butadiene/n-butanol flames was studied in a combined experimental and modeling work. The goal is to provide a detailed combustion chemistry model that allows for identification of the important pathways for butadiene and butanol oxidation as well as the formation of soot precursors and aromatics. Therefore, the chemical composition has been investigated for three low-pressure (20-30 Torr) premixed flames, with different shares of butanol ranging between 25% and 75% compared to butadiene in 50% argon. Mole fraction profiles of reactants, products, and intermediates including C3Hx and C4Hx radicals as well as mono-aromatics such as benzyl radicals, were measured quantitatively as a function of height above burner surface employing flame-sampled molecular-beam mass spectrometry (MBMS) utilizing photoionization with tunable vacuum-ultraviolet synchrotron radiation. The comparison of measured species profiles with modeling results provides a comprehensive view of the reaction model's quality and predictive capability with respect to the combustion chemistry of 1,3-butadiene and n-butanol under the current low-pressure, high-temperature conditions. In general, a good agreement was found between experimental and modeled results. Reaction flux and sensitivity analysis were used to get more insights into the combustion of the fuels.
Nawdiyal, A.; Hansen, Nils H.; Zeuch, T.; Seidel, L.; Mauß, F.
An existing detailed and broadly validated kinetic scheme is augmented to capture the flame chemistry of 1-hexene under stoichiometric and fuel rich conditions including benzene formation pathways. In addition, the speciation in a premixed stoichiometric 1-hexene flame (flat-flame McKenna-type burner) has been studied under a reduced pressure of 20-30 mbar applying flame-sampling molecular-beam time-of-flight mass spectrometry and photoionization by tunable vacuum-ultraviolet synchrotron radiation. Mole fraction profiles of 40 different species have been measured and validated against the new detailed chemical reaction model consisting of 275 species and 3047 reversible elementary reactions. A good agreement of modelling results with the experimentally observed mole fraction profiles has been found under both stoichiometric and fuel rich conditions providing a sound basis for analyzing benzene formation pathways during 1-hexene combustion. The analysis clearly shows that benzene formation via the fulvene intermediate is a very important pathway for 1-hexene.
This paper presents a detailed investigation of 2-methylbutanol combustion chemistry in low-pressure premixed flames. This chemistry is of particular interest to study because this compound is potentially a lignocellulosic-based, next-generation biofuel. The detailed chemical structure of a stoichiometric low-pressure (25 Torr) flame was determined using flame-sampling molecular-beam mass spectrometry. A total of 55 species were identified and subsequently quantitative mole fraction profiles as function of distance from the burner surface were determined. In an independent effort, a detailed flame chemistry model for 2-methylbutanol was assembled based on recent knowledge gained from combustion chemistry studies for butanol isomers ([Sarathy et al. Combust. Flame 159 (6) (2012) 2028-2055]) and iso-pentanol (3-methylbutanol) [Sarathy et al. Combust. Flame 160 (12) (2013) 2712-2728]. Experimentally determined and modeled mole fraction profiles were compared to demonstrate the model's capabilities. Examples of individual mole fraction profiles are discussed together with the most significant fuel consumption pathways to highlight the combustion chemistry of 2-methylbutanol. Discrepancies between experimental and modeling results are used to suggest areas where improvement of the kinetic model would be needed.
We have combined experimental and theoretical approaches to gain new insight into the mechanisms of PAH growth and soot formation. The experimental approach involves aerosol-mass spectrometry in conjunction with vacuum-ultraviolet photoionization of volatile species vaporizing from particles sampled from an Ar-diluted C2H2/O2 counter-flow diffusion flame at nearly atmospheric pressure (700 Torr). We recorded aerosol mass spectra at different distances from the fuel outlet for fixed ionization energies and in a fixed position while tuning the photoionization energy. The mass spectra contain a large distribution of peaks, highlighting the importance of small building blocks and showing a variety of chemical species that extends beyond the traditional classification of PAHs based on thermodynamic stability. In addition, we performed stochastic simulations of PAH growth in the flame in order to provide better insight into the chemical composition of species associated with peaks in the measured mass spectra. These simulations were conducted using a stochastic nanoparticle simulator (SNAPS). Synthesis of experimental and simulated results showed that peaks in the observed mass spectra generally consisted of a mixture of PAH isomers. At m/z =154 and 202, for example, experiments and simulations suggested that additional isomers than biphenyl and pyrene are important. Furthermore, the results highlight the importance of odd-carbon numbered species and complex growth paths. The experimental results suggest that species of higher masses can build up concentration ahead of species of lower masses. Our experimental results show, for example, that the peak at m/z = 278 appears closer to the burner outlet than the peak at m/z = 202, i.e., suggesting that a single monotonic growth mechanism is not enough.
In this study, two flames of iso-pentanol were stabilized on a 60-mm flat flame burner at a low pressure of 15 Torr and analyzed by a flame-sampling molecular-beam setup coupled to a mass spectrometer (MBMS). Singlephoton ionization by synchrotron-generated vacuum-UV radiation with high energy resolution (E/ΔE ∼0.04 eV) and/or electron ionization was combined with a custom-built reflectron time-of-flight spectrometer providing high mass resolution (m/Δm = 3000). Mole fraction profiles for more than 40 flame species and the temperature profile were determined experimentally. The flame temperatures were measured using OH laser induced fluorescence and used as input parameters for the model calculations. The experimental dataset was used to guide the development of a combustion chemistry model for the high-temperature oxidation chemistry of iso-pentanol. The chemical kinetic model is herein validated for the first time against detailed speciation profiles of combustion intermediates and product species including C5 branched aldehydes, enols, and alkenes. In a separated study, the model was validated against a number of different datasets including low and high temperature ignition delay in rapid compression machines and shock tubes, jet stirred reactor speciation data, premixed laminar flame speed, and opposed-flow diffusion flame strained extinction.
Cyclic ethers, like tetrahydrofuran (THF), are formed during the autoignition of alkanes and subsequently influence their combustion chemistry. To learn more about the oxidation chemistry of these ether intermediates, a fuel-rich THF flame (π = 1.75) has been studied using the versatile technique of flame-sampling Molecular Beam Mass Spectrometry (MBMS) in combination with single-photon ionization. Several cyclic intermediates which are potentially formed by dehydrogenation of the fuel are identified by their ionization energies. Ethylene, propene, ketene and formaldehyde are major stable decomposition products of THF and their mole fraction profiles are presented. Detected oxygenated species include ethenol, acetaldehyde and propanal. Despite the fuel-rich conditions, the concentrations of benzene and other aromatic hydrocarbons are near the detection limit.
This meeting will continue to cover fundamentals and applications of photoionization and photodetachment, including valence and core-level phenomena and applications to reaction dynamics, ultrashort laser pulses and the study of exotic molecules and anions.