This research effort examined the application of Nafion polymers in alcohol solvents as an anti-ice surface coating, as a mixture with hydrophilic polymers and freezing point depressant salt systems. Co-soluble systems of Nafion, polymer and salt were applied using dip coating methods to create smooth films for frost observation over a Peltier plate thermal system in ambient laboratory conditions. Cryo-DSC was applied to examine freezing events of the Nafion-surfactant mixtures, but the sensitivity of the measurement was insufficient to determine frost behavior. Collaborations with the Fog Chamber at Sandia-Albuquerque, and in environmental SAXS measurements with CINT-LANL were requested but were not able to be performed under the research duration. Since experimental characterization of these factors is difficult to achieve directly, computational modeling was used to guide the scientific basis for property improvement. Computational modeling was performed to improve understanding of the dynamic association between ionomer side groups and added molecules and deicing salts. The polyacrylic acid in water system was identified at the start of the project as a relevant system for exploring the effect of varying counterions on the properties of fully deprotonated polyacrylic acid (PAA) in the presence of water. Simulations were modeled with four different counterions, two monovalent counterions (K+ and Na+) and two divalent counterions (Ca2+ and Mg2+). The wt% of PAA in these systems was varied from ~10 to 80 wt% PAA for temperatures from 250K to 400K. In the second set of simulations, the interpenetration of water into a dry PAA film was studied for Na+ or Ca2+ counterions for temperatures between 300K and 400K. The result of this project is a sprayable Nafion film composite which resists ice nucleation at -20 °C for periods of greater than three hours. It is composed of Nafion polymer, hydrophilic polyethylene oxide polymer and CaCl2 anti-ice crosslinker. Durability and field performance properties remain to be determined.
Novel materials based on the aluminum oxyhydroxide boehmite phase were prepared using a glycothermal reaction in 1,4-butanediol. Under the synthesis conditions, the atomic structure of the boehmite phase is altered by the glycol solvent in place of the interlayer hydroxyl groups, creating glycoboehmite. The structure of glycoboehmite was examined in detail to determine that glycol molecules are intercalated in a bilayer structure, which would suggest that there is twice the expansion identified previously in the literature. This precursor phase enables synthesis of two new phases that incorporate either polyvinylpyrrolidone or hydroxylpropyl cellulose nonionic polymers. These new materials exhibit changes in morphology, thermal properties, and surface chemistry. All the intercalated phases were investigated using PXRD, HRSTEM, SEM, FT-IR, TGA/DSC, zeta potential titrations, and specific surface area measurement. These intercalation polymers are non-ionic and interact through wetting interactions and hydrogen bonding, rather than by chemisorption or chelation with the aluminum ions in the structure.
This report describes research and development (R&D) activities conducted during fiscal year 2021 (FY21) specifically related to the Engineered Barrier System (EBS) R&D Work Package in the Spent Fuel and Waste Science and Technology (SFWST) Campaign supported by the United States (U.S.) Department of Energy (DOE). The R&D activities focus on understanding EBS component evolution and interactions within the EBS, as well as interactions between the host media and the EBS. A primary goal is to advance the development of process models that can be implemented directly within the Generic Disposal System Analysis (GDSA) platform or that can contribute to the safety case in some manner such as building confidence, providing further insight into the processes being modeled, establishing better constraints on barrier performance, etc.
Stereolithography (SL) is a process that uses photosensitive polymer solutions to create 3D parts in a layer by layer approach. Sandia National Labs is interested in using SL for the printing of ceramic loaded resins, namely alumina, that we are formulating here at the labs. One of the most important aspects for SL printing of ceramics is the properties of the slurry itself. The work presented here will focus on the use of a novel commercially available low viscosity resin provided by Colorado Photopolymer Solutions, CPS 2030, and a Hypermer KD1 dispersant from Croda. Two types of a commercially available alumina powder, Almatis A16 SG and Almatis A15 SG, are compared to determine the effects that the size and the distribution of the powder have on the loading of the solution using rheology. The choice of a low viscosity resin allows for a high particle loading, which is necessary for the printing of high density parts using a commercial SL printer. The Krieger-Dougherty equation was used to evaluate the maximum particle loading for the system. This study found that a bimodal distribution of micron sized powder (A15 SG) reduced the shear thickening effects caused by hydroclusters, and allows for the highest alumina powder loading. A final sintered density of 90% of the theoretical density of alumina was achieved based on the optimized formulation and printing conditions.
Our results show that a pseudo-boehmite precursor material can be chemically modified with divalent cationic species, for example, Nickel, to create an effective getter for anionic species. The viability of this novel class of materials is established by a variety of characterization methods, including surface area measurements, scanning electron microscopy, elemental analysis, and sorption capacity measurements. We will present the results of sorption capacity and surface area measurements that show the high sorption capacity of this novel class of getter materials. Our study shows that the divalent cation modification can increase the sorption capacity by as much as a factor of two.
The impact on the morphology nanoceramic materials generated from group 4 metal alkoxides ([M(OR)4]) and the same precursors modified by 6,6'-(((2-hydroxyethyl)azanediyl)bis(methylene))bis(2,4-di- tert-butylphenol) (referred to as H3-AM-DBP2 (1)) was explored. The products isolated from the 1:1 stoichiometric reaction of a series of [M(OR)4] where M = Ti, Zr, or Hf; OR = OCH(CH3)2(OPr i); OC(CH3)3(OBu t); OCH2C(CH3)3(ONep) with H3-AM-DBP2 proved, by single crystal X-ray diffraction, to be [(ONep)Ti( k4( O,O',O'',N)-AM-DBP2)] (2), [(OR)M(μ( O)- k3( O',O'',N)-AM-DBP2)]2 [M = Zr: OR = OPr i, 3·tol; OBu t, 4·tol; ONep, 5·tol; M = Hf: OR = OBu t, 6·tol; ONep, 7·tol]. The product from each system led to a tetradentate AM-DBP2 ligand and retention of a parent alkoxide ligand. For the monomeric Ti derivative (2), the metal was solved in a trigonal bipyramidal geometry, whereas for the Zr (3-5) and Hf (6, 7) derivatives a symmetric dinuclear complex was formed where the ethoxide moiety of the AM-DBP2 ligand bridges to the other metal center, generating an octahedral geometry. High quality density functional theory level gas-phase electronic structure calculations on compounds 2-7 using Gaussian 09 were used for meaningful time dependent density functional theory calculations in the interpretation of the UV-vis absorbance spectral data on 2-7. Nanoparticles generated from the solvothermal treatment of the ONep/AM-DBP2 modified compounds (2, 5, 7) in comparison to their parent [M(ONep)4] were larger and had improved regularity and dispersion of the final ceramic nanomaterials.
The impact on the final morphology of yttria (Y2O3) nanoparticles from different ratios (100/0, 90/10, 65/35, and 50/50) of oleylamine (ON) and oleic acid (OA) via a solution precipitation route has been determined. In all instances, powder X-ray diffraction indicated that the cubic Y2O3 phase (PDF #00-025-1200) with the space group I-3a (206) had been formed. Analysis of the collected FTIR data revealed the presence of stretches and bends consistent with ON and OA, for all ratios investigated, except the 100/0. Transmission electron microscopy images revealed regular and elongated hexagons were produced for the ON (100/0) sample. As OA was added, the nanoparticle morphology changed to lamellar pillars (90/10), then irregular particles (65/35), and finally plates (50/50). The formation of the hexagonal-shaped nanoparticles was determined to be due to the preferential adsorption of ON onto the {101} planes. As OA was added to the reaction mixture, it was found that the {111} planes were preferentially coated, replacing ON from the surface, resulting in the various morphologies noted. The roles of the ratio of ON/OA in the synthesis of the nanocrystals were elucidated in the formation of the various Y2O3 morphologies, as well as a possible growth mechanism based on the experimental data.
The synthesis of a series of lanthanide trifluoroacetic acid (H-TFA) derivatives which contain only the TFA and its conjugate acid has been developed. From the reaction of Ln(N(SiMe3)2)3 with an excess amount of H-TFA, the products were identified as: [Ln(μ-TFA)3(H-TFA)2]n (Ln = Y, Ce, Sm, Eu, Gd, Tb, Dy), [Ln(μ-TFA)3(μ-H-TFA)]n·solv (Ln·solv = Pr·2 H-TFA, H3O+, Ho·2py, Er·py, Yb·py, H-TFA), 3[H][(TFA)La(μ-TFA)3La(TFA)(μ-TFA)2(μc-TFA)2]n ½(H2O) ½(H2O, H-TFA) (La·½(H2O) ½(H2O, H-TFA)), [(k2-TFA)Nd(μ-TFA)3]n·H-py+ (Nd·H-py+), [(py)2Tm(μ-TFA)3]n (Tm), or [Lu(μ-TFA)4Lu(μ-TFA)3·H3O+]n (Lu·H3O+). Here, the majority of samples formed long chain polymers with 3 or 4 μ-TFA ligands. Tm was isolated with py coordinated to the metal, whereas Ho, Er, and Yb were isolated with py located within the lattice. Select samples from this set of compounds were used to generate nanomaterials under solvothermal (SOLVO) conditions using pyridine (py) or octylamine at 185 °C for 24 h. The SOLVO products were isolated as: (i) from py: La – fluocerite (LaF3, PDF 98-000-0214, R = 9.64%, 35(0) nm), Tb – terbium fluoride (TbF3, PDF 00-037-1487, R = 4.76%, 21(2) nm), Lu lutetium oxy fluoride (LuOF, PDF 00-052-0779, R = 8.24%, 8(2) nm); (ii) from octylamine: La – fluocerite/lanthanum oxide carbonate (LaF3, PDF 98-000-0214, R = 7.47%, 5(0) nm; La2O2(CO3), PDF 01-070-5539, R = 12.32%, 12(0) nm), Tb – terbium oxy fluoride (TbOF, PDF 00-008-0230, R = 7.01%, 5(0) nm); Lu – lutetium oxide (Lu2O3, PDF 00-012-0728, R = 6.52%, 6(1) nm).
There is a rising interest in developing functional electronics using additively manufactured components. Considerations in materials selection and pathways to forming hybrid circuits and devices must demonstrate useful electronic function; must enable integration; and must complement the complex shape, low cost, high volume, and high functionality of structural but generally electronically passive additively manufactured components. This article reviews several emerging technologies being used in industry and research/development to provide integration advantages of fabricating multilayer hybrid circuits or devices. First, we review a maskless, noncontact, direct write (DW) technology that excels in the deposition of metallic colloid inks for electrical interconnects. Second, we review a complementary technology, aerosol deposition (AD), which excels in the deposition of metallic and ceramic powder as consolidated, thick conformal coatings and is additionally patternable through masking. Finally, we show examples of hybrid circuits/devices integrated beyond 2-D planes, using combinations of DW or AD processes and conventional, established processes.
The use of colloidal processing principles in the formation of ceramic materials is well appreciated for developing homogeneous material properties in sintered products, enabling novel forming techniques for porous ceramics or 3D printing, and controlling microstructure to enable optimized material properties. The solution processing of electronic ceramic materials often involves multiple cationic elements or dopants to affect microstructure and properties. Material stability must be considered through the steps of colloidal processing to optimize desired component properties. This review provides strategies for preventing material degradation in particle synthesis, milling processes, and dispersion, with case studies of consolidation using spark plasma sintering of these systems. The prevention of multication corrosion in colloidal dispersions can be achieved by utilizing conditions similar to the synthesis environment or by the development of surface passivation layers. The choice of dispersing surfactants can be related to these surface states, which are of special importance for nanoparticle systems. A survey of dispersant chemistries related to some commonsynthesis conditions is provided for perovskite systems as an example. These principles can be applied tomany colloidal systems related to electronic and optical applications.
The use of maltodextrin supramolecular structures (MD SMS) as a reducing agent and colloidal stabilizing agent for the synthesis of Ag nanoparticles (Ag NPs) identified three key points. First, the maltodextrin (MD) solutions are effective in the formation of well-dispersed Ag NPs utilizing alkaline solution conditions, with the resulting Ag NPs ranging in size from 5 to 50. nm diameter. Second, in situ characterization by Raman spectroscopy and small angle X-ray scattering (SAXS) are consistent with initial nucleation of Ag NPs within the MD SMS up to a critical size of ca. 1. nm, followed by a transition to more rapid growth by aggregation and fusion between MD SMS, similar to micelle aggregation reactions. Third, the stabilization of larger Ag NPs by adsorbed MD SMS is similar to hemi-micelle stabilization, and monomodal size distributions are proposed to relate to integer surface coverage of the Ag NPs. Conditions were identified for preparing Ag NPs with monomodal distributions centered at 30-35. nm Ag NPs.
High temperature solid state sodium (23Na) magic angle spinning (MAS) NMR spin lattice relaxation times (T1) were evaluated for a series of NASICON (Na3Zr2PS12O12) materials to directly determine Na jump rates. Simulations of the Ti temperature variations that incorporated distributions in Na jump activation energies, or distribution of jump rates, improved the agreement with experiment. The 23Na NMR T1 relaxation results revealed that distributions in the Na dynamics were present for all of the NASICON materials investigated here. The 23Na relaxation experiments also showed that small differences in material composition and/or changes in the processing conditions impacted the distributions in the Na dynamics. The extent of the distribution was related to the presence of a disordered or glassy phosphate phase present in these different sol-gel processed materials. The 23Na NMR T1 relaxation experiments are a powerful tool to directly probing Na jump dynamics and provide additional molecular level details that could impact transport phenomena.
As alternative energy generating devices (i.e., solar, wind, etc) are added onto the electrical energy grid (AC grid), irregularities in the available electricity due to natural occurrences (i.e., clouds reducing solar input or wind burst increasing wind powered turbines) will be dramatically increased. Due to their almost instantaneous response, modern flywheel-based energy storage devices can act a mechanical mechanism to regulate the AC grid; however, improved spin speeds will be required to meet the necessary energy levels to balance these green energy variances. Focusing on composite flywheels, we have investigated methods for improving the spin speeds based on materials needs. The so-called composite flywheels are composed of carbon fiber (C-fiber), glass fiber, and a glue (resin) to hold them together. For this effort, we have focused on the addition of fillers to the resin in order to improve its properties. Based on the high loads required for standard meso-sized fillers, this project investigated the utility of ceramic nanofillers since they can be added at very low load levels due to their high surface area. The impact that TiO2 nanowires had on the final strength of the flywheel material was determined by a three-point-bend test. The results of the introduction of nanomaterials demonstrated an increase in strength of the flywheels C-fiber-resin moiety, with an upper limit of a 30% increase being reported. An analysis of the economic impact concerning the utilization of the nanowires was undertaken and after accounting for new-technology and additional production costs, return on improved-nanocomposite investment was approximated at 4-6% per year over the 20-year expected service life. Further, it was determined based on the 30% improvement in strength, this change may enable a 20-30% reduction in flywheel energy storage cost ($/kW-h).
Magnesium batteries are alternatives to the use of lithium ion and nickel metal hydride secondary batteries due to magnesium's abundance, safety of operation, and lower toxicity of disposal. The divalency of the magnesium ion and its chemistry poses some difficulties for its general and industrial use. This work developed a continuous and fibrous nanoscale network of the cathode material through the use of electrospinning with the goal of enhancing performance and reactivity of the battery. The system was characterized and preliminary tests were performed on the constructed battery cells. We were successful in building and testing a series of electrochemical systems that demonstrated good cyclability maintaining 60-70% of discharge capacity after more than 50 charge-discharge cycles.
Development of high energy density dielectrics with low temperature coefficients of capacitance that are systems integrable are needed for extreme environment, defense and automotive applications. The synthesis of high purity chemically prepared Ca(Zr,Ti)O3 powders is described and has resulted in the lowering of conventional firing temperatures by over 100 C. Direct write aerosol spray deposition techniques have been used to fabricate high quality single layer and multilayer capacitors from these powders. The dielectric constants of the direct write capacitors are equivalent to those of fired bulk ceramics. Our presentation emphasizes the synthesis, phase evolution and microstructure development that has resulted in dielectrics with energy densities in excess of 3 J/cm3 with less than 1% change in dielectric constant over a 200 C temperature range.
Silver nanomaterials have significant application resulting from their optical properties related to surface enhanced Raman spectroscopy, high electrical conductivity, and anti-microbial impact. A 'green chemistry' synthetic approach for silver nanomaterials minimizes the environmental impact of silver synthesis, as well as lowers the toxicity of the reactive agents. Biopolymers have long been used for stabilization of silver nanomaterials during synthesis, and include gum Arabic, heparin, and common starch. Maltodextrin is a processed derivative of starch with lower molecular weight and an increase in the number of reactive reducing aldehyde groups, and serves as a suitable single reactant for the formation of metallic silver. Silver nanomaterials can be formed under either a thermal route at neutral pH in water or by reaction at room temperature under more alkaline conditions. Deposited silver materials are formed on substrates from near neutral pH solutions at low temperatures near 50 C. Experimental conditions based on material concentrations, pH and reaction time are investigated for development of deposited films. Deposit morphology and optical properties are characterized using SEM and UV-vis techniques. Silver nanoparticles are generated under alkaline conditions by a dissolution-reduction method from precipitated silver (II) oxide. Synthesis conditions were explored for the rapid development of stable silver nanoparticle dispersions. UV-vis absorption spectra, powder X-ray diffraction (PXRD), dynamic light scattering (DLS), and transmission electron microscopy (TEM) techniques were used to characterize the nanoparticle formation kinetics and the influence of reaction conditions. The adsorbed content of the maltodextrin was characterized using thermogravimetric analysis (TGA).
In an aim to develop photo-responsive composites, the UV photo-reduction of aqueous titanium oxide nanoparticle-graphene oxide (TiO{sub 2}-GO) dispersions (Lambert et al. J Phys. Chem. 2010 113 (46), 19812-19823) was undertaken. Photo-reduction led to the formation of a black precipitate as well as a soluble portion, comprised of titanium oxide nanoparticle-reduced graphene oxide (TiO{sub 2}-RGO). When allowed to slowly evaporate, self assembled titanium oxide nanoparticle-graphene oxide (SA-TiO{sub 2}-RGO) films formed at the air-liquid interface of the solution. The thickness of SARGO-TiO{sub 2} films range from {approx}30-100 nm when deposited on substrates, and appear to be comprised of a mosaic assembly of graphene nanosheets and TiO{sub 2}, as observed by scanning electron microscopy. Raman spectroscopy and X-ray photoelectron spectroscopy indicate that the graphene oxide is only partially reduced in the SA-TiO{sub 2}-RGO material. These films were also deposited onto inter-digitated electrodes and their photo-responsive behavior was examined. UV-exposure lead to a {approx} 200 kOhm decrease in resistance across the device, resulting in a cathodically biased film. The cathodic bias of the films was utilized for the subsequent reduction of Ag(NO{sub 3}) into silver (Ag) nanoparticles, forming a ternary Ag-(SA-RGO-TiO{sub 2}) composite. Various aspects of the self assembled films, their photoconductive properties as well as potential applications will be presented.
Lack of robust manufacturing capabilities have limited our ability to make tailored materials with useful optical and thermal properties. For example, traditional methods such as spontaneous self-assembly of spheres cannot generate the complex structures required to produce a full bandgap photonic crystals. The goal of this work was to develop and demonstrate novel methods of directed self-assembly of nanomaterials using optical and electric fields. To achieve this aim, our work employed laser tweezers, a technology that enables non-invasive optical manipulation of particles, from glass microspheres to gold nanoparticles. Laser tweezers were used to create ordered materials with either complex crystal structures or using aspherical building blocks.
This project uses advanced ceramic processes to fabricate large, optical-quality, polycrystalline lanthanum halide scintillators to replace small single crystals produced by the conventional Bridgman growth method. The new approach not only removes the size constraint imposed by the growth method, but also offers the potential advantages of both reducing manufacturing cost and increasing production rate. The project goal is to fabricate dense lanthanum halide ceramics with a preferred crystal orientation by applying texture engineering and solid-state conversion to reduce the thermal mechanical stress in the ceramic and minimize scintillation light scattering at grain boundaries. Ultimately, this method could deliver the sought-after high sensitivity and <3% energy resolution at 662 keV of lanthanum halide scintillators and unleash their full potential for advanced gamma ray detection, enabling rapid identification of radioactive materials in a variety of practical applications. This report documents processing details from powder synthesis, seed particle growth, to final densification and texture development of cerium doped lanthanum bromide (LaBr{sub 3}:Ce{sup +3}) ceramics. This investigation demonstrated that: (1) A rapid, flexible, cost efficient synthesis method of anhydrous lanthanum halides and their solid solutions was developed. Several batches of ultrafine LaBr{sub 3}:Ce{sup +3} powder, free of oxyhalide, were produced by a rigorously controlled process. (2) Micron size ({approx} 5 {micro}m), platelet shape LaBr{sub 3} seed particles of high purity can be synthesized by a vapor phase transport process. (3) High aspect-ratio seed particles can be effectively aligned in the shear direction in the ceramic matrix, using a rotational shear-forming process. (4) Small size, highly translucent LaBr{sub 3} (0.25-inch diameter, 0.08-inch thick) samples were successfully fabricated by the equal channel angular consolidation process. (5) Large size, high density, translucent LaBr{sub 3} ceramics samples (3-inch diameter, > 1/8-inch thick) were fabricated by hot pressing, demonstrating the superior manufacturability of the ceramic approach over single crystal growth methods in terms of size capability and cost. (6) Despite all these advances, evidence has shown that LaBr{sub 3} is thermally unstable at temperatures required for the densification process. This is particularly true for material near the surface where lattice defects and color centers can be created as bromine becomes volatile at high temperatures. Consequently, after densification these samples made using chemically prepared ultrafine powders turned black. An additional thermal treatment in a flowing bromine condition proved able to reduce the darkness of the surface layer for these densified samples. These observations demonstrated that although finer ceramic powders are desirable for densification due to a stronger driving force from their large surface areas, the same desirable factor can lead to lattice defects and color centers when these powders are densified at higher temperatures where material near the surface becomes thermally unstable.
The objective of the experimental effort is to provide a model particle system that will enable modeling of the macroscopic rheology from the interfacial and environmental structure of the particles and solvent or melt as functions of applied shear and volume fraction of the solid particles. This chapter describes the choice of the model particle system, methods for synthesis and characterization, and results from characterization of colloidal dispersion, particle film formation, and the shear and oscillatory rheology in the system. Surface characterization of the grafted PDMS interface, dispersion characterization of the colloids, and rheological characterization of the dispersions as a function of volume fraction were conducted.
Nanoparticle interactions and their impact on particle dispersion and rheology are well known to be functions of the interfacial structure between the particle and the fluid phase. The dispersion and flow properties of a titania nanopowder were evaluated in polydimethylsiloxane fluid using ''grafted to'' surface modification of the titania with short molecular weight PDMS polymers. The interaction energy between particles was modeled using analytical expressions as well as dynamic functional theory for polymer surface chains. Particle dynamics as a function of volume fraction were characterized using light scattering, acoustic spectroscopy, and shear and oscillatory measurements. Autophobic dewetting is a novel short range interaction in this system that may be impacting the maximum packing fraction of particles in a suspension.
The present work demonstrates the use of light to move liquids on a photoresponsive monolayer, providing a new method for delivering analyses in lab-on-chip environments for microfluidic systems. The light-driven motion of liquids was achieved on photoresponsive azobenzene modified surfaces. The surface energy components of azobenzene modified surfaces were calculated by Van Oss theory. The motion of the liquid was achieved by generation of a surface tension gradient by isomerization of azobenzene monolayers using UV and Visible light, thereby establishing a surface energy heterogeneity on the edge of the droplet. Contact angle measurements of various solvents were used to demonstrate the requirement for fluid motion.
This work reports on the grafting of methyl methacrylate polymer brushes containing spirobenzopyran pendant groups from flat silica surfaces and colloidal particles utilizing atom transfer radical polymerization (ATRP). The reaction conditions were optimized with respect to the kind of surface bound initiator, the type of halide and ligand used in the catalytic complex, the presence/absence of untethered initiator, and solvent type. This enabled synthesis of coatings up to 80 {+-} 3 nm thick with controlled spirobenzopyran content. While polymerization kinetics indicate the presence of chain termination reactions, the 'living' character of the process is confirmed by controlled formation of block copolymer brushes. UV/vis spectroscopy was used to characterize the UV-induced isomerization of spirobenzopyran to zwitterionic merocyanine and the thermal back-reaction. Spectral and kinetic analyses of this latter bleaching process points to the existence of free and associated merocyanines in the polymeric brush in both tetrahydrofuran and toluene. However, stabilization of merocyanine species by the polymer matrix is considerably greater in toluene with thermal back-reaction rates approaching those determined for solid dry films.
Colloidal particles were derivatized with end-grafted polymethylmethacryate polymer brushes containing varying concentrations of spirobenzopyran photochromic molecules. The polymers were grown from initiator-functionalized silica partilces by an atom-transfer radical polymerization (ATRP). These core-shell colloids formed stable suspensions in toluene with the spirobenzopyran in its closed, nonpolar form. However, UV-induced photoswitching of the photochrome to its open, polar merocyanine isomer caused rapid aggregation. The nature of this colloidal stability transition was examined with respect to the spirobenzopyran content in the polymeric brush and solvent polarity. Turbidimetry, wettability studies, UV-vis spectroscopy, suspension rheology, SEM, and visual inspection were utilized to characterize the system photoswitchability. It was found that the system exhibiting the greatest transition in toluene was the copolymer brush composed of 20% spirobenzopyran and 80% methyl methacrylate.
Quartz surfaces and colloidal silica particles were derivatized with a poly(methyl methacrylate) copolymer containing spirobenzopyran (SP) photochromic molecules in the pendant groups at a concentration of 20 mol %. Two-photon near-IR excitation ({approx}780 nm) was then used to create chemically distinct patterns on the modified surfaces through a photochromic process of SP transformation to the zwitterionic merocyanine (MC) isomer. The derivatized colloids were approximately 10 times more likely to adsorb onto the photoswitched, MC regions. Surface coverage and adsorption kinetics have been compared to the mean-field model of irreversible monolayer adsorption.
The manipulation of physical interactions between structural moieties on the molecular scale is a fundamental hurdle in the realization and operation of nanostructured materials and high surface area microsystem architectures. These include such nano-interaction-based phenomena as self-assembly, fluid flow, and interfacial tribology. The proposed research utilizes photosensitive molecular structures to tune such interactions reversibly. This new material strategy provides optical actuation of nano-interactions impacting behavior on both the nano- and macroscales and with potential to impact directed nanostructure formation, microfluidic rheology, and tribological control.
Chemically prepared zinc oxide powders are fabricated for the production of high aspect ratio varistor components. Colloidal processing in water was performed to reduce agglomerates to primary particles, form a high solids loading slurry, and prevent dopant migration. The milled and dispersed powder exhibited a viscoelastic to elastic behavioral transition at a volume loading of 43-46%. The origin of this transition was studied using acoustic spectroscopy, zeta potential measurements and oscillatory rheology. The phenomenon occurs due to a volume fraction solids dependent reduction in the zeta potential of the solid phase. It is postulated to result from divalent ion binding within the polyelectrolyte dispersant chain, and was mitigated using a polyethylene glycol plasticizing additive. Chemically prepared zinc oxide powders were processed for the production of high aspect ratio varistor components. Near net shape casting methods including slip casting and agarose gelcasting were evaluated for effectiveness in achieving a uniform green microstructure achieving density values near the theoretical maximum during sintering. The structure of the green parts was examined by mercury porisimetry. Agarose gelcasting produced green parts with low solids loading values and did not achieve high fired density. Isopressing the agarose cast parts after drying raised the fired density to greater than 95%, but the parts exhibited catastrophic shorting during electrical testing. Slip casting produced high green density parts, which exhibited high fired density values. The electrical characteristics of slip cast parts are comparable with dry pressed powder compacts. Alternative methods for near net shape forming of ceramic dispersions were investigated for use with the chemically prepared ZnO material. Recommendations for further investigation to achieve a viable production process are presented.
The purpose of this program was to investigate methods to characterize the colloidal stability of nanoparticles during the synthesis reaction, and to characterize their organization related to interparticle forces. Studies were attempted using Raman spectroscopy and ultrasonic attenuation to observe the nucleation and growth process with characterization of stability parameters such as the zeta potential. The application of the techniques available showed that the instrumentation requires high sensitivity to the concentration of the system. Optical routes can be complicated by the scattering effects of colloidal suspensions, but dilution can cause a lowering of signal that prevents collection of data. Acoustic methods require a significant particle concentration, preventing the observation of nucleation events. Studies on the dispersion of nanoparticles show that electrostatic routes are unsuccessful with molecular surfactants at high particle concentration due to electrostatic interaction collapse by counterions. The study of molecular surfactants show that steric lengths on the order of 2 nm are successful for dispersion of nanoparticle systems at high particle concentration, similar to dispersion with commercial polyelectrolyte surfactants.
Chemically prepared zinc oxide powders are fabricated for the production of high aspect ratio varistor components. Colloidal processing was performed to reduce agglomerates to primary particles, form a high solids loadingslurry, and prevent dopant migration. The milled and dispersed powder exhibited a viscoelastic to elastic behavioral transition at a volume loading of 43-46%. The origin of this transition was studied using acoustic spectroscopy, zeta potential measurements, and oscillatory rheology. The phenomenon occurs due to a volume fraction solids dependent reduction in the zeta potential of the solid phase. It is postulated to result from divalent ion binding within the polyelectrolyte dispersant chain and was mitigated using a polyethylene glycol plasticizing additive. This allowed for increased solids loading in the slurry and a green body fabrication study to be presented in our companion paper.
Chemically prepared zinc oxide powders were processed for the production of high aspect ratio varistor components (length/diameter >5). Near-net-shape casting methods including slip casting and agarose gelcasting were evaluated for effectiveness in achieving a uniform green microstructure that densifies to near theoretical values during sintering. The structure of the green parts was examined by mercury porisimetry. Agarose gelcasting produced green parts having low solids loading values and did not achieve high fired density. Isopressing the agarose cast parts after drying raised the fired density to greater than 95%, but the parts exhibited catastrophic shorting during electrical testing. Slip casting produced high green density parts, which exhibit high fired density values. The electrical characteristics of slip-cast parts are comparable with dry-pressed powder compacts.
The design, fabrication, and performance of a planar microbattery made from a silicon wafer with a bonded lid are presented. The battery is designed with two compartments, separated by four columns of micro-posts. These posts are 3 or 5 micrometers in diameter. The posts permit transport of liquid electrolyte, but stop particles of battery material from each compartment from mixing. The anode and cathode battery compartments, the posts, fill holes, and conductive vias are all made using high-aspect-ratio reactive ion (Bosch) etching. After the silicon wafer is completed, it is anodically bonded or adhesive bonded to a Pyrex{reg_sign} wafer lid. The battery materials are made from micro-disperse particles that are 3-5 micrometers in diameter. The lithium-ion chemistry is microcarbon mesobeads and lithium cobalt oxide. The battery capacity is 1.83 micro-amp-hrs/cm{sup 2} at a discharge rate of 25 microamps.
Calculations of the Hamaker constants representing the van der Waals interactions between conductor, resistor and dielectric materials are performed using Lifshitz theory. The calculation of the parameters for the Ninham-Parsegian relationship for several non-aqueous liquids has been derived based on literature dielectric data. Discussion of the role of van der Waals forces in the dispersion of particles is given for understanding paste formulation. Experimental measurements of viscosity are presented to show the role of dispersant truncation of attractive van der Waals forces.