Publications

Abstract not provided.

Nickel-doped α-MnO2 nanowires (Ni-α-MnO2) were prepared with 3.4% or 4.9% Ni using a hydrothermal method. A comparison of the electrocatalytic data for the oxygen reduction reaction (ORR) in alkaline electrolyte versus that obtained with α-MnO2 or Cu-α-MnO2 is provided. In general, Ni-α-MnO2 (e.g., Ni-4.9%) had higher n values (n = 3.6), faster kinetics (k = 0.015 cm s-1), and lower charge transfer resistance (RCT = 2264 Ω at half-wave) values than MnO2 (n = 3.0, k = 0.006 cm s-1, RCT = 6104 Ω at half-wave) or Cu-α-MnO2 (Cu-2.9%, n = 3.5, k = 0.015 cm s-1, RCT = 3412 Ω at half-wave), and the overall activity for Ni-α-MnO2 trended with increasing Ni content, i.e., Ni-4.9% > Ni-3.4%. As observed for Cu-α-MnO2, the increase in ORR activity correlates with the amount of Mn3+ at the surface of the Ni-α-MnO2 nanowire. Examining the activity for both Ni-α-MnO2 and Cu-α-MnO2 materials indicates that the Mn3+ at the surface of the electrocatalysts dictates the activity trends within the overall series. Single nanowire resistance measurements conducted on 47 nanowire devices (15 of α-MnO2, 16 of Cu-α-MnO2-2.9%, and 16 of Ni-α-MnO2-4.9%) demonstrated that Cu-doping leads to a slightly lower resistance value than Ni-doping, although both were considerably improved relative to the undoped α-MnO2. The data also suggest that the ORR charge transfer resistance value, as determined by electrochemical impedance spectroscopy, is a better indicator of the cation-doping effect on ORR catalysis than the electrical resistance of the nanowire. (Figure Presented).

Abstract not provided.

Abstract not provided.

Abstract not provided.

Manganese oxide/poly(3,4-ethylene-dioxythiophene) (MnO_x/ PEDOT) nanostructured hybrid thin films were prepared using a simple anodic electrodeposition process from aqueous solution, and then tested for oxygen reduction reaction (ORR) activity in alkaline electrolyte using rotating disk electrode and rotating ring disk electrode methods. MnO_x/PEDOT provided improvements over MnO_x-only and PEDOT-only control films, with > 0.2 V decrease in onset and half-wave overpotentials, and > 1.5 times increase in terminal current density. The MnO_x/PEDOT film exhibited only a slightly lower n value (n = 3.86-3.92) than the 20% Pt/C benchmark electrocatalyst (n = 3.98) across all potentials. MnO_x/PEDOT also displayed a more positive half-wave potential and superior electrocatalytic selectivity for the ORR upon methanol exposure than 20% Pt/C. Here, the high activity and synergism of MnO_x/PEDOT towards the ORR is attributed to effective intermixing/dispersion of the two materials, intimate substrate contact with improved charge transfer processes attained by co-electrodepositing MnO_x with PEDOT and due to the increase in Mn³⁺ content at the surface of the oxide.

Cobalt phosphide based thin films and nanoparticles were prepared by the thermal phosphidation of spinel Co₃O₄ precursor films and nanoparticles, respectively. CoP films were prepared with overall retention of the Co₃O₄ nanoplatelet morphology while the spherical/cubic Co₃O₄ and Ni_0.15Co_2.85O₄ nanoparticles were converted to nanorods or nanoparticles, respectively. The inclusion of nickel in the nanoparticles resulted in a 2.5 fold higher surface area leading to higher gravimetric performance. In each case high surface area structures were obtained with CoP as the primary phase. All materials were found to act as effective bifunctional electrocatalysts for both the HER and the OER and compared well to commercial precious metal benchmark materials in alkaline electrolyte. As a result, a symmetrical water electrolysis cell prepared from the CoP-based film operated at a low overpotential of 0.41-0.51 V.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Cobalt phosphide based thin films and nanoparticles were prepared by the thermal phosphidation of spinel Co3O4 precursor films and nanoparticles, respectively. CoP films were prepared with overall retention of the Co3O4 nanoplatelet morphology while the spherical/cubic Co3O4 and Ni0.15Co2.85O4 nanoparticles were converted to nanorods or nanoparticles, respectively. The inclusion of nickel in the nanoparticles resulted in a 2.5 fold higher surface area leading to higher gravimetric performance. In each case high surface area structures were obtained with CoP as the primary phase. All materials were found to act as effective bifunctional electrocatalysts for both the HER and the OER and compared well to commercial precious metal benchmark materials in alkaline electrolyte. A symmetrical water electrolysis cell prepared from the CoP-based film operated at a low overpotential of 0.41-0.51 V.

Abstract not provided.

Abstract not provided.

Abstract not provided.

The role of Cu-ion doping in α-MnO2 electrocatalysts for the oxygen reduction reaction in alkaline electrolyte was investigated. Cu-doped α-MnO2 nanowires (Cu-α-MnO2) were prepared with varying amounts (up to ∼3%) of Cu2+ using a hydrothermal method. The electrocatalytic data indicate that Cu-α-MnO2 nanowires have up to 74% higher terminal current densities, 2.5 times enhanced kinetic rate constants, and 66% lower charge transfer resistances that trend with Cu content, exceeding values attained by α-MnO2 alone. The observed improvement in catalytic behavior correlates with an increase in Mn3+ content at the surface of the Cu-α-MnO2 nanowires. The Mn3+/Mn4+ couple is the mediator for the rate-limiting redox-driven O2/OH- exchange. O2 adsorbs via an axial site (the eg orbital on the Mn3+ d4 ion) at the surface or at edge defects of the nanowire, and the increase in covalent nature of the nanowire with Cu-ion doping leads to stabilization of O2 adsorbates and faster rates of reduction. A smaller crystallite size (roughly half) for Cu-α-MnO2 leading to a higher density of (catalytic) edge defect sites was also observed. This work is applicable to other manganese oxide electrocatalysts and shows for the first time there is a correlation for manganese oxides between electrocatalytic activity for the oxygen reduction reaction (ORR) in alkaline electrolyte and an increase in Mn3+ character at the surface of the oxide. © 2014 American Chemical Society.

Abstract not provided.

Silver-graphene nanoribbons (Ag-GNRs) were prepared from the chemical unzipping of multiwalled carbon nanotubes (MWCNTs) by reaction with Na/K alloy, Ag(O2CCH3) and then CH3OH. Ag-GNRs exhibited improved electrocatalytic ability for the oxygen reduction reaction (ORR) in 0.1M KOH as compared to the underlying GNR substrate alone and displayed an earlier onset and higher currents than a commercial Ag/Carbon (Ag/C) catalyst. The Ag-GNR hybrid demonstrates an outstanding tolerance to CH3OH crossover which exceeds that of the commercial benchmark, 20% Pt/C. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Abstract not provided.

Abstract not provided.

Abstract not provided.

Abstract not provided.