Resurrecting a battery chemistry thought to be only primary, we demonstrate the first example of a rechargeable alkaline zinc/copper oxide battery. With the incorporation of a Bi2O3additive to stabilize the copper oxide-based conversion cathode, Zn/(CuO-Bi2O3) cells are capable of cycling over 100 times at >124 W h/L, with capacities from 674 mA h/g (cycle 1) to 362 mA h/g (cycle 150). The crucial role of Bi2O3in facilitating the electrochemical reversibility of Cu2O, Cu(OH)2, and Cuowas supported by scanning and transmission electrochemical microscopy, cyclic voltammetry, and rotating ring-disc electrode voltammetry and monitoredvia operandoenergy-dispersive X-ray diffraction measurements. Bismuth was identified as serving two roles, decreasing the cell resistance and promoting Cu(I) and Cu(II) reduction. To mitigate the capacity losses of long-term cycling CuO cells, we demonstrate two limited depth of discharge (DOD) strategies. First, a 30% DOD (202 mA h/g) retains 99.9% capacity over 250 cycles. Second, the modification of the CuO cathode by the inclusion of additional Cu metal enables performance at very high areal capacities of ∼40 mA h/cm2and unprecedented energy densities of ∼260 W h/L, with near 100% Coulombic efficiency. This work revitalizes a historically primary battery chemistry and opens opportunity to future works in developing copper-based conversion cathode chemistries for the realization of low-cost, safe, and energy-dense secondary batteries.
Batteries for grid storage applications must be inexpensive, safe, reliable, as well as have a high energy density. Here, we utilize the high capacity of sulfur (S) (1675 mAh g-1, based on the idealized redox couple of S2./S) in order to demonstrate for the first time, a reversible high capacity solid-state S-based cathode for alkaline batteries. To maintain S in the solid-state, it is bound to copper (Cu), initially in its fully reduced state as the sulfide. Upon charging, the sulfide is oxidized to a polysulfide species which is captured and maintained in the solid-state by the Cu ions. This solid-state sulfide/polysulfide cathode was analyzed versus a zinc (Zn) anode which gives a nominal >1.2 V cell voltage based on the sulfide/polysulfide redox cathode chemistry. It was found that in order for the S cathode to have the best cycle life in the solid-state it must not only be bound to Cu ions but bound to Cu ions in the +1 valence state, forming Cu2S as a discharge product. Zn/Cu2S batteries cycled between 1.45 V and 0.4 V vs. Zn displayed capacities of 1500 mAh g-1 (based on mass of S) or i300 mAh g-1 (based on mass of Cu2S) and high areal (>23 mAh cm.2) and energy densities (>135 Wh L-1), but suffered from moderate cycle lifes (<250 cycles). The failure mechanism of this electrode was found to be disproportionation of the charged S species into irreversible sulfite releasing the bound Cu ions. The Cu ions become free to perform Cu specific redox reactions which slowly changes the battery redox chemistry from that of S to that of Cu with a S additive. Batteries utilizing the Cu2S cathode and a 50% depth of charge (DOC) cathode cycling protocol, with 5 wt% Na2S added to the electrolyte, retained a cathode capacity of 838 mAh g-1 (based on the mass of S) or 169 mA h g-1 (based on mass of Cu2S) after 450 cycles with >99.7% coulombic efficiency. These Zn/Cu2S batteries provided a grid storage relevant energy density of >42Wh L-1 (at 65 wt% Cu2S loading), despite only using a 3% depth of discharge (DOD) for the Zn anode. This work opens the way to a new class of energy dense grid storage batteries based on high capacity solid-state S-based cathodes.
Anodic stripping voltammetry (ASV) is an analysis technique that permits the selective and quantitative analysis of metal ion species in solution. It is most commonly applied in neutral to acidic electrolyte largely due to inherent metal ion solubility. Bismuth (Bi) is a common film used for ASV due to its good sensitivity, overall stability and insensitivity to O2. ASV, utilizing a Bi film, along with cadmium (Cd) and lead (Pb) as the plating mediators, has recently been adapted to determine zinc (Zn) concentrations in highly alkaline environments (30 % NaOH or 35 % M KOH). Successful analysis of Zn in alkaline relies on the ability of the hydroxide to form soluble metal anion species, such as Bi(OH)4 − and Zn(OH)4 2−. Here, we look to extend this technique to detect and quantify copper (Cu) ions in these highly basic electrolytes. However, in general, the use of ASV to detect and quantify Cu ion concentrations is notoriously difficult as the Cu stripping peak potential overlays with that of Bi from the common Bi film electrode. Here, an ASV method for determining Cu concentration in alkaline solutions is developed utilizing Pb as a deposition mediator. As such, it was found that when analyzing Cu solutions in the presence of Pb, the stripping voltammetry curves present separate and defined Cu stripping peaks. Different analyzes were made to find the best stripping voltammetry performance conditions. As such, an accumulation time of 5 minutes, an accumulation potential of≤−1.45 V vs. Hg/HgO, and a concentration of 35 wt% KOH were determined to be the conditions that presented the best ASV results. Utilizing these conditions, calibration curves in the presence of 5.0 ppm Pb showed the best linear stripping signal correlation with an r-squared value of 0.991 and a limit of detection (LOD) of 0.67 ppm. These results give way to evaluating Cu concentrations using ASV in aqueous alkaline solutions.