Ultradoping introduces unprecedented dopant levels into Si, which transforms its electronic behavior and enables its use as a next-generation electronic material. Commercialization of ultradoping is currently limited by gas-phase ultra-high vacuum requirements. Solvothermal chemistry is amenable to scale-up. However, an integral part of ultradoping is a direct chemical bond between dopants and Si, and solvothermal dopant-Si surface reactions are not well-developed. This work provides the first quantified demonstration of achieving ultradoping concentrations of boron (∼1e14 cm2) by using a solvothermal process. Surface characterizations indicate the catalyst cross-reacted, which led to multiple surface products and caused ambiguity in experimental confirmation of direct surface attachment. Density functional theory computations elucidate that the reaction results in direct B−Si surface bonds. This proof-of-principle work lays groundwork for emerging solvothermal ultradoping processes.
Recent news reports coming from Asia and the UK have highlighted the emerging threats of Non-Traditional Agents (NTAs) to national security. The UK incident underscores how NTAs may linger in the environment and at trace. Building on Sandia's extensive analytical chemistry work in this field, a polysilphenylene analog of Sandia's proprietary DKAP polymer coatings was synthesized and evaluated for high temperature operation. Initial test results are inconclusive as to the improved thermal stability of the new polymer with TGA/DSC results indicating a lower glass transition go temperature for the new "Hot DKAP" material and a similar to slightly lower start to mass loss for "Hot DKAP", but slower degradation rate in clean dry air. Additional testing with a TGA-MS system to identify what the fragments lost as a function of temperature is still needed to fully characterize the materials thermal properties. In addition, the material still needs to be evaluated for thermodynamic properties for analytes of interest using either GC or SPC coated devices. ACKNOWLEDGEMENTS The authors would like to gratefully acknowledge the contributions and assistance of Eric Coker and Lindsey Hughes.
We report a novel approach whereby cross-linked polybutadiene (PB) networks can be depolymerized in situ based on thermally activated alkene metathesis. A commercially available latent Ru catalyst, HeatMet, was compared to the common second-generation Hoveyda-Grubbs catalyst, HG2, in the metathetic depolymerization of PB. HeatMet was found to possess exceptional stability and negligible activity toward PB under ambient conditions, in solution and in bulk. This enabled cross-linked networks to be prepared containing homogeneously distributed Ru catalyst. The dynamic mechanical properties of networks containing HeatMet and cross-linked using alcohol-isocyanate or thiol-ene chemistry were evaluated during cross-linking and post-cross-linking under isothermal and nonisothermal heating. In both cases, above minimum catalyst loadings ranging from 0.004 to 0.024 mol %, the networks exhibited rapid degelation into a soluble oil upon heating to 100 °C. At these temperatures, extensive depolymerization of the PB segments through ring-closing metathesis of 1,4/1,2 diads by the activated HeatMet introduced network defects in significantly greater proportion than the original number of cross-links. The in situ depolymerization of cross-linked PB networks through latent catalysis, as described here, may enable facile disposal and recycling of PB encapsulants and adhesives, among other applications.
A small, consumable-free, low-power, ultra-high-speed comprehensive GC×GC system consisting of microfabricated columns, nanoelectromechanical system (NEMS) cantilever resonators for detection, and a valve-based stop-flow modulator is demonstrated. The separation of a highly polar 29-component mixture covering a boiling point range of 46 to 253 °C on a pair of microfabricated columns using a Staiger valve manifold in less than 7 seconds, and just over 4 seconds after the ensemble holdup time is demonstrated with a downstream FID. The analysis time of the second dimension was 160 ms, and peak widths in the second dimension range from 10-60 ms. A peak capacity of just over 300 was calculated for a separation of just over 6 s. Data from a continuous operation testing over 40 days and 20000 runs of the GC×GC columns with the NEMS resonators using a 4-component test set is presented. The GC×GC-NEMS resonator system generated second-dimension peak widths as narrow as 8 ms with no discernable peak distortion due to under-sampling from the detector.
We describe for the first time hydrogen bonded acid (HBA) polymer, poly[methyl[3-(2-hydroxyl, 4,6-bistrifluoromethyl)- phenyl]propylsiloxane], (DKAP), as stationary phase for gas chromatography (μGC) of organophosphate (OP), chemical warfare agent (CWA) surrogates, dimethylmethylphosphonate (DMMP), diisopropylmethylphosphonate (DIMP), diethylmethylphosphonate (DEMP), and trimethylphosphate (TMP), with high selectivity. Absorption of OPs to DKAP was one-to-several orders of magnitude higher relative to commercial polar, mid-polar, and nonpolar stationary phases. We also present for the first-time thermodynamic studies on the absorption of OP vapors and quantitative binding energy data for interactions with various stationary phases. These data help to identify the best pair of hetero-polar columns for a two-dimensional GC system, employing a nonpolar stationary phase as GC1 and DKAP as the GC2 stationary phase, for selective and rapid field detection of CWAs.
Gas Chromatography (GC) is routinely used in the laboratory to temporally separate chemical mixtures into their constituent components for improved chemical identification. This paper will provide a overview of more than twenty years of development of one-dimensional field-portable micro GC systems, highlighting key experimental results that illustrate how a reduction in false alarm rate (FAR) is achieved in real-world environments. Significantly, we will also present recent results on a micro two-dimensional GC (micro GCxGC) technology. This ultra-small system consists of microfabricated columns, NanoElectroMechanical System (NEMS) cantilever resonators for detection, and a valve-based stop-flow modulator. The separation of a 29-component polar mixture in less than 7 seconds is demonstrated along with peak widths in the second dimension ranging from 10-60 ms. For this system, a peak capacity of just over 300 was calculated for separation in about 6 s. This work has important implications for field detection, to drastically reduce FAR and significantly improve chemical selectivity and identification. This separation performance was demonstrated with the NEMS resonator and bench scale FID. But other detectors, suitably fast and sensitive can work as well. Recent research has shown that the identification power of GCxGC-FID can match that of GC-MS. This result indicates a path to improved size, weight, power, and performance in micro GCxGC systems outfitted with relatively non-specific, lightweight detectors. We will briefly discuss the performance of possible options, such as the pulsed discharge helium ionization detector (PDHID) and miniature correlation ion mobility spectrometer (mini-CIMS).
This report catalogues the results of a project exploring the incorporation of organometallic compounds into thermosetting polymers as a means to reduce their residual stress. Various syntheses of polymerizable ferro cene derivatives were attempted with mixed success. Ultimately, a diamine derivative of ferrocene was used as a curing agen t for a commercial epoxy resin, where it was found to give similar cure kinetics and mechanical properties in comparison to conventional curing agents. T he ferrocen e - based material is uniquely able to relax stress above the glass transition, leading to reduced cure stress. We propose that this behavior arises from the fluxional capacity of ferrocene. In support of this notion, nuclear magnetic resonance spectroscopy indicates a substantial increase in chain flexibility in the ferrocene - containing network. Although t he utilization of fluxionality is a novel approach to stress management in epoxy thermosets, it is anticipated to have greater impact in radical - cured ther mosets and linear polymers.
Physical stress relaxation in rubbery, thermoset polymers is limited by cross-links, which impede segmental motion and restrict relaxation to network defects, such as chain ends. In parallel, the cure shrinkage associated with thermoset polymerizations leads to the development of internal residual stress that cannot be effectively relaxed. Recent strategies have reduced or eliminated such cure stress in thermoset polymers largely by exploiting chemical relaxation processes, wherein temporary cross-links or otherwise transient bonds are incorporated into the polymer network. Here, we explore an alternative approach, wherein physical relaxation is enhanced by the incorporation of organometallic sandwich moieties into the backbone of the polymer network. A standard epoxy resin is cured with a diamine derivative of ferrocene and compared to conventional diamine curing agents. The ferrocene-based thermoset is clearly distinguished from the conventional materials by reduced cure stress with increasing cure temperature as well as unique stress relaxation behavior above its glass transition in the fully cured state. The relaxation experiments exhibit features characteristic of a physical relaxation process. Furthermore, the cure stress is observed to vanish precipitously upon deliberate introduction of network defects through an increasing imbalance of epoxy and amine functional groups. We postulate that these beneficial properties arise from fluxional motion of the cyclopentadienyl ligands on the polymer backbone.
We demonstrate matter-wave interference in a warm vapor of rubidium atoms. Established approaches to light-pulse atom interferometry rely on laser cooling to concentrate a large ensemble of atoms into a velocity class resonant with the atom optical light pulse. In our experiment, we show that clear interference signals may be obtained without laser cooling. This effect relies on the Doppler selectivity of the atom interferometer resonance. This interferometer may be configured to measure accelerations, and we demonstrate that multiple interferometers may be operated simultaneously by addressing multiple velocity classes.
The in-situ hydrolysis and subsequent condensation reaction of the chemical agent simulant diethyl chlorophosphate (DECP) was characterized by high-resolution 31P NMR spectroscopy following the addition of water in sub-equimolar concentrations. The identification and quantification of the multiple pyrophosphate and larger polyphosphate chemical species formed through a series of self-condensation reactions are reported. The DECP hydrolysis kinetics and distribution of breakdown species was strongly influenced by the water concentration and reaction temperature.
Preparation of sodium zirconium silicate phosphate (NaSICon), Na1+xZr2SixP3–xO12 (0.25 ≤ x ≤ 1.0), thin films has been investigated via a chemical solution approach on platinized silicon substrates. Increasing the silicon content resulted in a reduction in the crystallite size and a reduction in the measured ionic conductivity. Processing temperature was also found to affect microstructure and ionic conductivity with higher processing temperatures resulting in larger crystallite sizes and higher ionic conductivities. The highest room temperature sodium ion conductivity was measured for an x = 0.25 composition at 2.3 × 10–5 S/cm. In conclusion, the decreasing ionic conductivity trends with increasing silicon content and decreasing processing temperature are consistent with grain boundary and defect scattering of conducting ions.
Deboronation is observed during the reductive amination of formylphenylboronic acid (FPBA) to the amine termini and side chains of peptides. This deboronation is sensitive to the isomerism of the boronic acid (BA), with ortho-FPBA yielding complete deboronation in the preparation of an N-terminally-modified dipeptide. The observed behavior is also clearly mediated by the chemical identity of the amine substrate. These results reveal a previously undocumented subtlety of BA functionalization and highlight the importance of thorough spectroscopic characterization in the preparation of peptide and small molecule BAs.
Evaluating the stability of coupling reagents, quality control (QC), and surface functionalization metrology are all critical to the production of high quality peptide microarrays. We describe a broadly applicable screening technique for evaluating the fidelity of solid phase peptide synthesis (SPPS), the stability of activation/coupling reagents, and a microarray surface metrology tool. This technique was used to assess the stability of the activation reagent 1-{[1-(Cyano-2-ethoxy-2-oxo-ethylidenaminooxy)dimethylamino-morpholinomethylene]}methaneaminiumHexafluorophosphate (COMU) (Sigma-Aldrich, St. Louis, MO, USA) by SPPS of Leu-Enkephalin (YGGFL) or the coupling of commercially synthesized YGGFL peptides to (3-aminopropyl)triethyoxysilane-modified glass surfaces. Coupling efficiency was quantitated by fluorescence signaling based on immunoreactivity of the YGGFL motif. It was concluded that COMU solutions should be prepared fresh and used within 5 h when stored at ∼23 °C and not beyond 24 h if stored refrigerated, both in closed containers. Caveats to gauging COMU stability by absorption spectroscopy are discussed. Commercial YGGFL peptides needed independent QC, due to immunoreactivity variations for the same sequence synthesized by different vendors. This technique is useful in evaluating the stability of other activation/coupling reagents besides COMU and as a metrology tool for SPPS and peptide microarrays.
Optical fluorescence-based DNA assays are commonly used for pathogen detection and consist of an optical substrate containing DNA capture molecules, binding of target RNA or DNA sequences, followed by detection of the hybridization event with a fluorescent probe. Though fluorescence detection can offer exquisite signal-to-background ratios, with high specificity, vast opportunities exist to improve current optical-based genomic sensing approaches. For these reasons, there is a clear need to explore alternative optical sensing paradigms to alleviate these restrictions. Bio-templated nanomaterial synthesis has become a powerful concept for developing new platforms for bio-sensing, as the biomolecule of interest can act as part of the sensing transducer mechanism. We explored the use of DNA origami structures to immobilize gold nanoparticles in very precise localized arrangements producing unique optical absorption properties with implications in novel DNA sensing schemes. We also explored the use of in-situ TEM as a novel characterization method for DNA-nanoparticle assemblies.
Modification of the dipeptide of phenylalanine, FF, with a boronic acid (BA) functionality imparts unique aqueous self-assembly behavior that responds to multiple stimuli. Changes in pH and ionic strength are used to trigger hydrogelation via the formation of nanoribbon networks. Thus, we show for the first time that the binding of polyols to the BA functionality can modulate a peptide between its assembled and disassembled states.
Polycarbonate is a desirable material for many applications due to its favorable mechanical and optical properties. Here, we report a simple, safe, environmentally friendly aqueous method that uses diamines to functionalize a polycarbonate surface with amino groups. The use of water as the solvent for the functionalization ensures that solvent induced swelling does not affect the optical or mechanical properties of the polycarbonate. We characterize the efficacy of the surface amination using X-ray photo spectroscopy, Fourier transform infrared spectroscopy (FT-IR), atomic force microscopy (AFM), and contact angle measurements. Furthermore, we demonstrate the ability of this facile method to serve as a foundation upon which other functionalities may be attached, including antifouling coatings and oriented membrane proteins. (Chemical Presented).
The ability of three aryldiazonium salts to spontaneously assemble onto the surface of type 440C stainless steel is investigated in acetonitrile (ACN) and the model hydraulic fluids tributyl phosphate (TBP) and hexamethyldisiloxane (HMDS). Competition between native oxide formation and organic film growth at different diazonium salt concentrations is monitored by electrochemical impedance spectroscopy. At 1 mM diazonium salt, 70% of total assembly is complete within 10 min, though total surface coverage by organics is limited to ≈0.15 monolayers. Adding HCl to the electrolyte renders native oxide formation unfavorable, yet the diazonium molecules are still unable to the increase surface coverage over 1 M-10 μM HCl in solution. X-ray photoelectron spectroscopy confirms preferential bonding of organic molecules to iron over chromium, while secondary ion mass spectroscopy reveals the ability of these films to self-heal when mechanically removed or damaged. Aging the diazonium salts in these nonaqueous environments demonstrates that up to 90% of the original diazonium salt concentration remains after 21 days at room temperature, while increasing the temperature beyond 50 °C results in complete decomposition within 24 h, regardless of solvent-salt combination. It is concluded that the investigated diazonium molecules will not spontaneously form a continuous monolayer on 440C stainless steel immersed in ACN, TBP, or HMDS.
Electro-optical organic materials hold great promise for the development of high-efficiency devices based on exciton formation and dissociation, such as organic photovoltaics (OPV) and organic light-emitting devices (OLEDs). However, the external quantum efficiency (EQE) of both OPV and OLEDs must be improved to make these technologies economical. Efficiency rolloff in OLEDs and inability to control morphology at key OPV interfaces both reduce EQE. Only by creating materials that allow manipulation and control of the intimate assembly and communication between various nanoscale excitonic components can we hope to first understand and then engineer the system to allow these materials to reach their potential. The aims of this proposal are to: 1) develop a paradigm-changing platform for probing excitonic processes composed of Crystalline Nanoporous Frameworks (CNFs) infiltrated with secondary materials (such as a complimentary semiconductor); 2) use them to probe fundamental aspects of excitonic processes; and 3) create prototype OPVs and OLEDs using infiltrated CNF as active device components. These functional platforms will allow detailed control of key interactions at the nanoscale, overcoming the disorder and limited synthetic control inherent in conventional organic materials. CNFs are revolutionary inorganic-organic hybrid materials boasting unmatched synthetic flexibility that allow tuning of chemical, geometric, electrical, and light absorption/generation properties. For example, bandgap engineering is feasible and polyaromatic linkers provide tunable photon antennae; rigid 1-5 nm pores provide an oriented, intimate host for triplet emitters (to improve light emission in OLEDs) or secondary semiconducting polymers (creating a charge-separation interface in OPV). These atomically engineered, ordered structures will enable critical fundamental questions to be answered concerning charge transport, nanoscale interfaces, and exciton behavior that are inaccessible in disordered systems. Implementing this concept also creates entirely new dimensions for device fabrication that could both improve performance, increase durability, and reduce costs with unprecedented control of over properties. This report summarizes the key results of this project and is divided into sections based on publications that resulted from the work. We begin in Section 2 with an investigation of light harvesting and energy transfer in a MOF infiltrated with donor and acceptor molecules of the type typically used in OPV devices (thiophenes and fullerenes, respectively). The results show that MOFs can provide multiple functions: as a light harvester, as a stabilizer and organizer or the infiltrated molecules, and as a facilitator of energy transfer. Section 3 describes computational design of MOF linker groups to accomplish light harvesting in the visible and facilitate charge separation and transport. The predictions were validated by UV-visible absorption spectroscopy, demonstrating that rational design of MOFs for light-harvesting purposes is feasible. Section 4 extends the infiltration concept discussed in Section to, which we now designate as "Molecule@MOF" to create an electrically conducting framework. The tailorability and high conductivity of this material are unprecedented, meriting publication in the journal Science and spawning several Technical Advances. Section 5 discusses processes we developed for depositing MOFs as thin films on substrates, a critical enabling technology for fabricating MOF-based electronic devices. Finally, in Section 6 we summarize results showing that a MOF thin film can be used as a sensitizer in a DSSC, demonstrating that MOFs can serve as active layers in excitonic devices. Overall, this project provides several crucial proofs-of- concept that the potential of MOFs for use in optoelectronic devices that we predicted several years ago [ 3 ] can be realized in practice.