A three-dimensional direct numerical simulation (DNS) is performed for a turbulent hydrogen-air flame, represented with detailed chemistry, stabilized in a model gas-turbine combustor. The combustor geometry consists of a mixing duct followed by a sudden expansion and a combustion chamber, which represents a geometrically simplified version of Ansaldo Energia's GT26/GT36 sequential combustor design. In this configuration, a very lean blend of hydrogen and vitiated air is prepared in the mixing duct and convected into the combustion chamber, where the residence time from the inlet of the mixing duct to the combustion chamber is designed to coincide with the ignition delay time of the mixture. The results show that when the flame is stabilized at its design position, combustion occurs due to both autoignition and flame propagation (deflagration) modes at different locations within the combustion chamber. A chemical explosive mode analysis (CEMA) reveals that most of the fuel is consumed due to autoignition in the bulk-flow along the centerline of the combustor, and lower amounts of fuel are consumed by flame propagation near the corners of the sudden expansion, where the unburnt temperature is reduced by the thermal wall boundary layers. An unstable operating condition is also identified, wherein periodic auto-ignition events occur within the mixing duct. These events appear upstream of the intended stabilization position, due to positive temperature fluctuations induced by pressure waves originating from within the combustion chamber. The present DNS investigation represents the initial step of a comprehensive research effort aimed at gaining detailed physical insight into the rate-limiting processes that govern the sequential combustor behavior and avoid the insurgence of the off-design auto-ignition events.
The ignition process in diesel engines is highly complex and incompletely understood. In the present study, two-dimensional direct numerical simulations are performed to investigate the ignition dynamics and their sensitivity to thermochemical and mixing parameters. The thermochemical and mixing conditions are matched to the benchmark Spray A experiment from the Engine Combustion Network. The results reveal a complex ignition process with overlapping stages of: low-temperature ignition (cool flames), rich premixed ignition, and nonpremixed ignition, which are qualitatively consistent with prior experimental and numerical investigations, however, this is the first time that fully-resolved simulations have been reported at the actual Spray A thermochemical condition. Parametric variations are then performed for the Damkohler number Da, oxidiser temperature, oxygen concentration, and peak mixture fraction (a measure of premixedness), to study their effect on the ignition dynamics. It is observed that with both increasing oxidiser temperature and decreasing oxygen concentration, that the cool flame moves to richer mixtures, the overlap in the ignition stages decreases, and the (nondimensional) time taken to reach a fully burning state increases. With increasing Da, the cool-flame speed is decreased due to lower mean mixing rates, which causes a delayed onset of high-temperature ignition. With increasing peak mixture fraction, the onset of each stage of ignition is not affected, but the overall duration of the ignition increases leading to a longer burn duration. Overall, the results suggest that turbulence-chemistry interactions play a significant role in determining the timing and location in composition space of the entire ignition process.
Laminar natural gas flames are investigated at engine-relevant thermochemical conditions where the ignition delay time ? is short due to very high ambient temperatures and pressures. At these conditions, it is not possible to measure or calculate well-defined values for the laminar flame speed s l , laminar flame thickness ? l , and laminar flame time scale 1l/sl due to the explosive thermochemical state. Here, the corresponding reference values, s R , ? R , and RRsR that account for the effects of autoignition, are numerically estimated to investigate the enhancement of flame propagation, and the competition with autoignition that arises under nominally autoignitive conditions (characterised here by the number ?/? R ). Large values of ?/? R indicate that autoignition is unimportant, values near or below unity indicate that flame propagation is not possible, and intermediate values indicate that a combination of both flame propagation and autoignition may be important, depending upon factors such as device geometry, turbulence, stratification, et cetera. The reference quantities are presented for a wide range of temperatures, equivalence ratios, pressures, and hydrogen concentrations, which includes conditions relevant to stationary gas turbine reheat burners and boosted spark ignition engines. It is demonstrated that the transition from flame propagation to autoignition is only dependent on residence time, when the results are non-dimensionalised by the reference values. The temporal evolution of the reference values are also reported for a modelled boosted SI engine. It is shown that the nominally autoignitive conditions enhance flame propagation, which may be an ameliorating factor for the onset of engine knock. The calculations are performed using a recently-developed, detailed 177 species mechanism for C0-C3 chemistry that is derived from theoretical chemistry and is suitable for a wide range of thermochemical conditions as it is not tuned or optimised for a particular operating condition.
A three-dimensional direct numerical simulation is conducted for a temporally evolving planar jet of n-heptane at a pressure of 40 atmospheres and in a coflow of air at 1100 K. At these conditions, n-heptane exhibits a two-stage ignition due to low- and high-temperature chemistry, which is reproduced by the global chemical model used in this study. The results show that ignition occurs in several overlapping stages and multiple modes of combustion are present. Low-temperature chemistry precedes the formation of multiple spatially localised high-temperature chemistry autoignition events, referred to as 'kernels'. These kernels form within the shear layer and core of the jet at compositions with short homogeneous ignition delay times and in locations experiencing low scalar dissipation rates. An analysis of the kernel histories shows that the ignition delay time is correlated with the mixing rate history and that the ignition kernels tend to form in vortically dominated regions of the domain, as corroborated by an analysis of the topology of the velocity gradient tensor. Once ignited, the kernels grow rapidly and establish edge flames where they envelop the stoichiometric isosurface. A combination of kernel formation (autoignition) and the growth of existing burning surface (via edge-flame propagation) contributes to the overall ignition process. An analysis of propagation speeds evaluated on the burning surface suggests that although the edge-flame speed is promoted by the autoignitive conditions due to an increase in the local laminar flame speed, edge-flame propagation of existing burning surfaces (triggered initially by isolated autoignition kernels) is the dominant ignition mode in the present configuration.
A two-dimensional direct numerical simulation of the ignition at diesel engine-relevant conditions was performed at 40 atm and at 900 K ambient temperature using dimethyl ether (DME) as the fuel with a 30 species reduced chemical mechanism. At these conditions similar to diesel fuel DME exhibited two-stage ignition. The low-temperature chemistry analysis revealed a "spotty" first-stage autoignition in lean regions which transitions to a diffusively supported cool-flame and then propagates up the local mixture fraction gradient towards richer regions. The cool-flame speed was much faster than can be attributed to spatial gradients in first-stage ignition delay time in homogeneous reactors and it caused a shortening of the second-stage ignition delay times compared to a homogeneous reactor wherein the shortening became more pronounced at richer mixtures. Multiple high-temperature ignition kernels were noted over a range of rich mixtures that are much richer than the homogeneous most reactive mixture and most kernels formed much earlier than suggested by the homogeneous ignition delay time of the corresponding local mixture.
With the goal of providing a more detailed fundamental understanding of ignition processes in diesel engines, this study reports analysis of a direct numerical simulation (DNS) database. In the DNS, a pseudo turbulent mixing layer of dimethyl ether (DME) at 400 K and air at 900 K is simulated at a pressure of 40 atmospheres. At these conditions, DME exhibits a two-stage ignition and resides within the negative temperature coefficient (NTC) regime of ignition delay times, similar to diesel fuel. The analysis reveals a complex ignition process with several novel features. Autoignition occurs as a distributed, two-stage event. The high-temperature stage of ignition establishes edge flames that have a hybrid premixed/autoignition flame structure similar to that previously observed for lifted laminar flames at similar thermochemical conditions. A combustion mode analysis based on key radical species illustrates the multi-stage and multi-mode nature of the ignition process and highlights the substantial modelling challenge presented by diesel combustion.